Motorola 2.1 Installation Guide Page 547
- Page / 952
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
PROFILES 7 - 109
Parameters
Usage Guidelines
errdisable recovery [cause
bpduguard |interval
<10-1000000>]
• Disables error
• recovery – Enables the timeout mechanism for a port to be
recovered
• cause bpduguard – Specifies the reason for errdisable
• bpduguard – Recovers from errdisable due to bpduguard
• interval <10-1000000> – Specifies the interval after which a port
is enabled
• <10-1000000> – Specifies an errdisable-timeout interval in
seconds.
mst [<0-15> priority
<0-61440>| cisco-interoperability
[enable|disable] |enable|
forward-time <4-30> |hello-time
<1-10>|instance
<1-15>|max-age <4-60> |
max-hops <7-127>|region
<LINE>|revision <0-255>]
Configures multiple spanning tree commands
• <0-15> – Specifies the number of instances required for
configuration
• priority <0-61440> – Sets the bridge priority for an instance to
the value specified. Use the no parameter with this command to
restore the default bridge priority value
• <0-61440> – Bridge priority in increments of 4096 (Lower
priority indicates greater likelihood of becoming root)
• cisco-interoperability [enable|disable] – Enables/disables CISCO
interoperability
• Enable – Enables the multiple spanning tree protocol
• forward-time <4-30> – Specifies the forwarding delay time in
seconds between 4 -30
• hello-time <1-10> – Specifies the hello BDPU interval in seconds
within the range 1-10
• Instance <1-15> – Defines the instance ID to which the VLAN is
associated
• max-age <4-60> – Maximum time to listen for the root bridge in
seconds. Enter a value between 4 and 60
• max-hop <7-127> – Maximum hops when BPDU is valid
• region <LINE> – MST region
• revision <0-255> – Sets the revision number of the MST bridge.
• <0-255> – Defines the revision number for configuration
information
portfast [bpdufilter| bpduguard]
default
Enables the portfast feature on a bridge
• bpdufilter default – Use the bpdu-filter command to set the BPDU
filter for the port. Use the no parameter with this command to
revert the port BPDU filter value to the default value.
The Spanning Tree Protocol sends BPDUs from all ports. Enabling
the BPDU Filter feature ensures PortFast enabled ports do not
transmit or receive BPDUs
• bpduguard default – Guards portfast ports against BPDU receive
• default – Enables the BPDU filter on portfast enabled ports by
default
- Motorola Solutions 1
- MOTOROLA SOLUTIONS WING 5 3
- CLI REFERENCE GUIDE 3
- Revision History 5
- TABLE OF CONTENTS 7
- Table of Contents 3 9
- Table of Contents 5 11
- Table of Contents 7 13
- Table of Contents 9 15
- Table of Contents 11 17
- About This Guide 19
- Document Set 20
- Document Convention 21
- Notational Conventions 22
- About This Guide 17 23
- 18 WiNG CLI Reference Guide 24
- Customer Support Web Site 25
- General Information 25
- Motorola, Inc 26
- End-User License Agreement 26
- About This Guide 21 27
- 22 WiNG CLI Reference Guide 28
- CHAPTER 1 INTRODUCTION 29
- 1.1 CLI Overview 31
- Table 1.1 All Modes Commands 32
- INTRODUCTION 1 - 5 33
- INTRODUCTION 1 - 7 35
- 1.3 Using the No Command 37
- • Command Output pagination 38
- INTRODUCTION 1 - 11 39
- 1.4.4 Creating Profiles 40
- 1.4.6 Remote Administration 41
- 1.4.6.2 Configuring ssh 42
- INTRODUCTION 1 - 15 43
- User Exec commands: 45
- 2.1 User Exec Commands 46
- USER EXEC MODE COMMANDS 2 - 3 47
- 2.1.1 ap-upgrade 48
- USER EXEC MODE COMMANDS 2 - 5 49
- 2.1.2 change-passwd 51
- 2.1.3 clear 52
- USER EXEC MODE COMMANDS 2 - 9 53
- 2.1.4 clock 55
- 2.1.5 clrscr 56
- 2.1.6 cluster 57
- 2.1.7 commit 58
- 2.1.8 connect 59
- 2.1.9 crypto 60
- – Performs an 62
- 2.1.10 disable 69
- 2.1.11 enable 70
- 2.1.12 exit 71
- 2.1.13 help 72
- 2.1.14 logging 76
- 2.1.15 mint 77
- 2.1.16 no 79
- 2.1.17 page 80
- 2.1.18 ping 81
- 2.1.19 revert 82
- 2.1.20 service 83
- 2.1.21 show 84
- 2.1.22 telnet 86
- 2.1.23 terminal 87
- 2.1.24 time-it 88
- 2.1.25 traceroute 89
- 2.1.26 watch 90
- 2.1.27 write 91
- 3.1.1 ap-upgrade 97
- 3.1.2 archive 100
- 3.1.3 boot 101
- 3.1.4 cd 102
- 3.1.5 change-passwd 103
- 3.1.6 clear 104
- Parameters 105
- 3.1.7 clock 107
- 3.1.8 clrscr 108
- 3.1.9 cluster 109
- 3.1.10 configure 110
- 3.1.11 commit 111
- 3.1.12 connect 112
- 3.1.13 copy 113
- 3.1.14 crypto 114
- – Performs 116
- 3.1.15 delete 123
- 3.1.16 disable 124
- 3.1.17 diff 125
- 3.1.18 dir 126
- 3.1.19 edit 127
- 3.1.20 enable 128
- 3.1.21 erase 129
- 3.1.22 exit 130
- 3.1.23 format 131
- 3.1.24 halt 132
- 3.1.25 help 133
- 37FABE> 136
- 3.1.26 logging 137
- 3.1.27 mkdir 138
- 3.1.28 mint 139
- 3.1.29 more 141
- 3.1.30 no 142
- 3.1.31 page 143
- 3.1.32 ping 144
- 3.1.33 pwd 145
- 3.1.34 reload 146
- 3.1.35 rename 147
- 3.1.36 revert 148
- 3.1.37 rmdir 149
- 3.1.38 self 150
- 3.1.39 service 151
- 3.1.40 show 152
- 3.1.41 telnet 154
- 3.1.42 terminal 155
- 3.1.43 time-it 156
- 3.1.44 traceroute 157
- 3.1.45 upgrade 158
- 3.1.46 upgrade-abort 159
- 3.1.47 watch 160
- 3.1.48 write 161
- COMMANDS 163
- 4.1.1 aaa-policy 166
- 4.1.2 advanced-wips-policy 167
- 4.1.3 ap650 168
- 4.1.4 ap6511 169
- 4.1.5 ap6532 170
- 4.1.6 ap71xx 171
- 4.1.7 association-acl-policy 172
- 4.1.9 captive portal 174
- 4.1.9.1 captive-portal 175
- 4.1.9.2.1 access-time 177
- 4.1.9.2.2 access-type 178
- 4.1.9.2.3 accounting 179
- 4.1.9.2.4 connection-mode 180
- 4.1.9.2.5 custom-auth 181
- 4.1.9.2.6 inactivity-timeout 182
- 4.1.9.2.7 server 183
- 4.1.9.2.8 simultaneous-users 184
- 4.1.9.2.9 terms-agreement 185
- 4.1.9.2.10use 186
- 4.1.9.2.11webpage-location 187
- 4.1.9.2.12webpage 188
- external fail www.symbol.com 190
- 4.1.10 clear 191
- Global Configuration Commands 192
- 4.1.11.2.1monitor 195
- 4.1.11.2.2no 196
- 4.1.12 customize 197
- 4.1.13 device 202
- 4.1.14 device-categorization 203
- 4.1.14.2.1mark-device 206
- 4.1.14.2.2no 207
- 4.1.15 dhcp-server-policy 208
- 4.1.16 dns-whitelist 209
- 4.1.16.1 dns-whitelist 210
- 4.1.16.2.1permit 212
- 4.1.16.2.2no 213
- 4.1.17 do 214
- 4.1.18 end 216
- 4.1.19 event-system-policy 217
- 4.1.19.1 event-system-policy 218
- 4.1.19.2.1event 220
- 4.1.19.2.2no 230
- 4.1.20 firewall-policy 231
- 4.1.21 help 232
- 4.1.22 host 234
- 4.1.23 igmp-snoop-policy 235
- 4.1.24 ip 236
- 4.1.25 mac 237
- 4.1.26 management-policy 238
- 4.1.27 mint-policy 239
- 4.1.28 nac-list 240
- 4.1.28.1 nac-list 241
- 4.1.28.2 nac-list-mode 242
- 4.1.28.2.1exclude 243
- 4.1.28.2.2include 244
- 4.1.28.2.3no 245
- 4.1.29 no 246
- 4.1.30 password-encryption 248
- 4.1.31 profile 249
- 4.1.32 radio-qos-policy 251
- 4.1.33 radius-group 252
- 4.1.34 radius-server-policy 253
- 4.1.36 rf-domain 255
- 4.1.36.1 rf-domain 256
- 4.1.36.2 rf-domain-mode 257
- 4.1.36.2.1channel-list 258
- 4.1.36.2.2control-vlan 259
- 4.1.36.2.3layout 260
- 4.1.37 rfs4000 261
- 4.1.39 rfs7000 263
- 4.1.40 role-policy 264
- 4.1.41 self 265
- 4.1.42 service 266
- 4.1.43 show 268
- 4.1.44 smart-rf-policy 270
- 4.1.45 wips-policy 271
- 4.1.46 wlan 272
- 4.1.46.1 wlan 273
- 4.1.46.2 wlan-mode commands 274
- Table 4.17 wlan-mode commands 275
- 4.1.46.2.1802.11k 276
- 4.1.46.2.2802.11r 277
- 4.1.46.2.3802.11w 278
- 4.1.46.2.4accounting 279
- 4.1.46.2.5acl 280
- 4.1.46.2.7authentication-type 282
- 4.1.46.2.8bridging-mode 283
- 4.1.46.2.9broadcast-dhcp 284
- 4.1.46.2.10broadcast-ssid 285
- 4.1.46.2.12client-access 287
- 4.1.46.2.15data-rates 290
- 4.1.46.2.16description 293
- 4.1.46.2.17encryption-type 294
- 4.1.46.2.18enforce-dhcp 295
- 4.1.46.2.19ip 296
- 4.1.46.2.20kerberos 297
- 4.1.46.2.22no 300
- 4.1.46.2.23proxy-arp-mode 301
- 4.1.46.2.24radius 302
- 4.1.46.2.25shutdown 303
- 4.1.46.2.26ssid 304
- 4.1.46.2.27use 305
- 4.1.46.2.28vlan 306
- 4.1.46.2.29vlan-pool-member 307
- 4.1.46.2.30wep128 308
- 4.1.46.2.31wep64 309
- 4.1.46.2.32wireless-client 310
- 4.1.46.2.33wpa-wpa2 312
- encryption-type none 314
- authentication-type none 314
- 4.1.47 wlan-qos-policy 315
- 4.1.48 write 316
- CHAPTER 5 COMMON COMMANDS 317
- 5.1 Common Commands 318
- 5.1.1 clrscr 319
- 5.1.2 commit 320
- 5.1.3 exit 321
- 5.1.4 help 322
- COMMON COMMANDS 5 - 7 323
- COMMON COMMANDS 5 - 9 325
- 5.1.5 no 326
- COMMON COMMANDS 5 - 11 327
- 5.1.6 show 328
- COMMON COMMANDS 5 - 13 329
- 5.1.7 revert 330
- 5.1.8 service 331
- COMMON COMMANDS 5 - 17 333
- COMMON COMMANDS 5 - 19 335
- COMMON COMMANDS 5 - 21 337
- COMMON COMMANDS 5 - 23 339
- COMMON COMMANDS 5 - 25 341
- COMMON COMMANDS 5 - 27 343
- ParametersPrivilege Exec Mode 344
- COMMON COMMANDS 5 - 29 345
- COMMON COMMANDS 5 - 31 347
- COMMON COMMANDS 5 - 33 349
- System Information: 350
- 5.1.9 write 351
- CHAPTER 6 SHOW COMMANDS 353
- 6.1 show commands 354
- SHOW COMMANDS 6 - 3 355
- Table 6.1 show commands 356
- 6.1.1 show 357
- PRIVILEGE EXEC Mode 358
- SHOW COMMANDS 6 - 7 359
- 6.1.2 adoption 360
- SHOW COMMANDS 6 - 9 361
- 6.1.3 advanced-wips 362
- SHOW COMMANDS 6 - 11 363
- 6.1.4 ap-upgrade 365
- 6.1.5 boot 366
- 6.1.6 captive-portal 367
- – Specifies an 368
- – Selection based on state 368
- 6.1.7 cdp 369
- 6.1.8 clock 370
- 6.1.9 cluster 371
- 6.1.10 commands 372
- SHOW COMMANDS 6 - 21 373
- 6.1.11 context 374
- SHOW COMMANDS 6 - 23 375
- 6.1.12 critical-resources 376
- 6.1.13 crypto 377
- SHOW COMMANDS 6 - 27 379
- 6.1.14 debug 380
- SHOW COMMANDS 6 - 29 381
- 6.1.15 debugging 382
- SHOW COMMANDS 6 - 31 383
- 6.1.16 device-categorization 384
- 6.1.17 event-history 385
- 6.1.18 event-system-policy 386
- 6.1.19 file 387
- 6.1.20 firewall 388
- SHOW COMMANDS 6 - 37 389
- SHOW COMMANDS 6 - 39 391
- 6.1.21 interface 392
- SHOW COMMANDS 6 - 41 393
- 6.1.22 ip 394
- SHOW COMMANDS 6 - 43 395
- SHOW COMMANDS 6 - 45 397
- 6.1.23 ip-access-list-stats 399
- 6.1.24 licenses 400
- 6.1.25 lldp 401
- 6.1.26 logging 402
- 6.1.27 mac-access-list-stats 403
- 6.1.28 mac-address-table 404
- 6.1.29 mint 405
- 6.1.30 noc 407
- online 408
- 6.1.31 ntp 409
- 6.1.32 password-encryption 410
- 0-37FAAA 411
- 6.1.34 remote-debug 412
- 6.1.35 rf-domain-manager 413
- 6.1.36 role 414
- 6.1.37 running-config 415
- hostname rfs7000-37FABE 416
- 6.1.38 session-changes 417
- 6.1.39 session-config 418
- 6.1.40 sessions 419
- 6.1.41 smart-rf 420
- SHOW COMMANDS 6 - 69 421
- 6.1.42 spanning-tree 422
- SHOW COMMANDS 6 - 71 423
- 6.1.43 startup-config 425
- 6.1.44 terminal 426
- 6.1.45 timezone 427
- 6.1.46 upgrade-status 428
- 6.1.47 version 429
- 6.1.48 wireless 430
- SHOW COMMANDS 6 - 79 431
- SHOW COMMANDS 6 - 81 433
- 011 wireless controller 433
- status on ap7131-889EC4 434
- SHOW COMMANDS 6 - 83 435
- 4000-880DA7 on rfs4000-880DA7 435
- 6.1.49 wwan 437
- CHAPTER 7 PROFILES 439
- 7.1 Creating Profiles 440
- PROFILES 7 - 3 441
- 7.1.1 aaa 442
- PROFILES 7 - 5 443
- 7.1.2 arp 444
- PROFILES 7 - 7 445
- Creating Profiles 446
- 7.1.4 autoinstall 447
- 7.1.5 ap-upgrade 448
- 7.1.6 bridge commands 449
- 7.1.6.1 bridge 450
- PROFILES 7 - 13 451
- 7.1.6.2.1 bridging-mode 452
- PROFILES 7 - 15 453
- 7.1.6.2.2 description 453
- 7.1.6.2.3 edge-vlan 454
- 7.1.6.2.4 ip 454
- PROFILES 7 - 17 455
- 7.1.6.2.5 no 456
- PROFILES 7 - 19 457
- 7.1.6.2.7 use 458
- 7.1.7 cdp 459
- 7.1.8 cluster 460
- PROFILES 7 - 23 461
- 7.1.10 controller 463
- 7.1.11 crypto 465
- PROFILES 7 - 29 467
- 7.1.12 isakmp-policy 469
- 7.1.12.1 authentication 470
- PROFILES 7 - 33 471
- 7.1.12.2 encryption 471
- 7.1.12.3 group 472
- PROFILES 7 - 35 473
- 7.1.12.4 hash 473
- 7.1.12.5 lifetime 474
- PROFILES 7 - 37 475
- 7.1.12.6 no 475
- 7.1.13 crypto-group 476
- PROFILES 7 - 39 477
- 7.1.13.1 dns 477
- 7.1.13.2 wns 478
- 7.1.14 dscp-mapping 479
- 7.1.15 email-notification 480
- PROFILES 7 - 43 481
- 7.1.16 enforce-version 482
- PROFILES 7 - 45 483
- 7.1.17 events 484
- 7.1.18 ip 485
- PROFILES 7 - 49 487
- 7.1.19 nat-pool 489
- 7.1.19.1 address 490
- PROFILES 7 - 53 491
- 7.1.19.2 no 491
- 7.1.20 interface 492
- PROFILES 7 - 55 493
- PROFILES 7 - 57 495
- 7.1.21.1 cdp 496
- PROFILES 7 - 59 497
- 7.1.21.2 channel-group 497
- 7.1.21.3 description 498
- PROFILES 7 - 61 499
- 7.1.21.4 dot1x 499
- 7.1.21.5 duplex 500
- PROFILES 7 - 63 501
- 7.1.21.6 ip 501
- 7.1.21.7 lldp 502
- PROFILES 7 - 65 503
- 7.1.21.8 no 503
- 7.1.21.9 power 504
- PROFILES 7 - 67 505
- 7.1.21.10 qos 505
- 7.1.21.11 shutdown 506
- PROFILES 7 - 69 507
- 7.1.21.12 spanning-tree 507
- PROFILES 7 - 71 509
- 7.1.21.13 speed 509
- 7.1.21.14 switchport 510
- PROFILES 7 - 73 511
- 7.1.21.15 use 512
- PROFILES 7 - 75 513
- 7.1.22.1 crypto 514
- PROFILES 7 - 77 515
- 7.1.22.2 description 515
- 7.1.22.3 dhcp-relay-incoming 516
- PROFILES 7 - 79 517
- 7.1.22.4 ip 517
- 7.1.22.5 no 518
- PROFILES 7 - 81 519
- 7.1.22.6 shutdown 519
- 7.1.22.7 use 520
- 7.1.23 led 521
- 7.1.24 legacy-auto-downgrade 522
- 7.1.25 legacy-auto-update 523
- 7.1.26 lldp 524
- 7.1.27 load-balancing 525
- [ap-load-weightage 526
- 7.1.28 local 527
- 7.1.29 logging 528
- PROFILES 7 - 91 529
- 7.1.30 mac-address-table 530
- 7.1.31 mint 531
- PROFILES 7 - 95 533
- 7.1.33 monitor 535
- 7.1.35 neighbor-info-interval 537
- 7.1.36 no 538
- 7.1.37 noc 539
- 7.1.38 ntp 540
- PROFILES 7 - 103 541
- 7.1.40 power-config 542
- 7.1.41 radius 543
- 7.1.42 rf-domain-manager 544
- 7.1.43 service 545
- 7.1.44 spanning-tree 546
- PROFILES 7 - 109 547
- 7.1.45 use 549
- 7.1.46 vpn 551
- 7.1.47 wep-shared-key-auth 552
- 7.2 Device Specific Commands 553
- Command Description Reference 554
- 7.2.1 ap-upgrade 555
- 7.2.2 area 556
- 7.2.3 contact 557
- 7.2.4 country-code 558
- 7.2.5 dhcp-redundancy 559
- 7.2.6 floor 560
- 7.2.7 hostname 561
- 7.2.8 layout-coordinates 562
- 7.2.9 location 563
- 7.2.10 mac-name 564
- 7.2.11 neighbor-info-interval 565
- 7.2.12 override-wlan 566
- 7.2.13 remove-override 567
- 7.2.14 rsa-key 568
- 7.2.15 sensor-server 569
- 7.2.16 stats 570
- 7.2.17 timezone 571
- 7.2.18 trustpoint 572
- 7.2.19 wwan 573
- CHAPTER 8 AAA-POLICY 575
- 8.1 aaa-policy 576
- 8.1.1 accounting 577
- AAA-POLICY 8 - 5 579
- 8.1.2 authentication 581
- AAA-POLICY 8 - 9 583
- 8.1.3 mac-address-format 585
- 8.1.4 no 586
- 8.1.5 server-pooling-mode 587
- 8.1.6 use 588
- 8.1.7 write 589
- 8.1.8 clrscr 591
- 8.1.9 commit 592
- 8.1.10 do 593
- 8.1.11 end 595
- 8.1.12 exit 596
- 8.1.13 health-check 597
- 8.1.14 help 598
- 8.1.15 revert 599
- 8.1.16 service 600
- AAA-POLICY 8 - 27 601
- 8.1.17 show 602
- AAA-POLICY 8 - 29 603
- 9.1 auto-provisioning-policy 606
- 9.1.1 adopt 607
- 9.1.2 default-adoption 610
- 9.1.3 deny 611
- 9.1.4 no 613
- 10.1 advanced-wips-policy 616
- 10.1.1 event 617
- ADVANCED-WIPS-POLICY 10 - 5 619
- ADVANCED-WIPS-POLICY 10 - 7 621
- 10.1.2 no 622
- 10.1.3 server-listen-port 623
- 10.1.4 terminate 624
- 10.1.5 use 625
- 11.1 association-acl-policy 628
- 11.1.1 deny 629
- 11.1.2 no 630
- 11.1.3 permit 631
- Chapter 12 ACCESS-LIST 633
- 12.1 ip-access-list 635
- 12.1.1 deny 636
- ACCESS-LIST 12 - 5 637
- ACCESS-LIST 12 - 7 639
- 12.1.2 permit 641
- ACCESS-LIST 12 - 11 643
- ACCESS-LIST 12 - 13 645
- any log rule-precedence 200 646
- 12.1.3 no 647
- 12.1.4 write 648
- ACCESS-LIST 12 - 17 649
- 12.1.5 clrscr 650
- 12.1.6 commit 651
- 12.1.7 end 652
- 12.1.8 exit 653
- 12.1.9 help 654
- 12.1.10 revert 655
- 12.1.11 service 656
- ACCESS-LIST 12 - 25 657
- 12.1.12 show 658
- 12.2 mac-access-list 659
- 12.2.1 permit 660
- ACCESS-LIST 12 - 29 661
- ACCESS-LIST 12 - 31 663
- ACCESS-LIST 12 - 33 665
- 12.2.2 deny 667
- ACCESS-LIST 12 - 37 669
- Usage Guidelines 670
- ACCESS-LIST 12 - 39 671
- CHAPTER 13 DHCP-SERVER-POLICY 673
- 13.1 dhcp-server-policy 674
- 13.1.1 bootp 675
- 13.1.2 dhcp-pool 676
- 13.1.3 dhcp-pool-mode 677
- 13.1.3.1 address 678
- DHCP-SERVER-POLICY 13 - 7 679
- 13.1.3.2 bootfile 679
- 13.1.3.3 ddns 680
- DHCP-SERVER-POLICY 13 - 9 681
- 13.1.3.4 default-router 681
- 13.1.3.5 dns-server 682
- DHCP-SERVER-POLICY 13 - 11 683
- 13.1.3.6 domain-name 683
- 13.1.3.7 excluded-address 684
- DHCP-SERVER-POLICY 13 - 13 685
- 13.1.3.8 lease 685
- client-name test4lease 686
- DHCP-SERVER-POLICY 13 - 15 687
- 13.1.3.9 netbios-name-server 687
- 13.1.3.10 netbios-node-type 688
- DHCP-SERVER-POLICY 13 - 17 689
- 13.1.3.11 next-server 689
- 13.1.3.12 no 690
- DHCP-SERVER-POLICY 13 - 19 691
- 13.1.3.13 option 691
- 13.1.3.14 respond-via-unicast 692
- DHCP-SERVER-POLICY 13 - 21 693
- 13.1.3.15 update 693
- 13.1.4 static-binding 694
- DHCP-SERVER-POLICY 13 - 23 695
- 13.1.5 static-binding-mode 696
- DHCP-SERVER-POLICY 13 - 25 697
- 13.1.5.1 bootfile 697
- 13.1.5.2 client-name 698
- DHCP-SERVER-POLICY 13 - 27 699
- 13.1.5.3 default-router 699
- 13.1.5.4 dns-server 700
- DHCP-SERVER-POLICY 13 - 29 701
- 13.1.5.5 domain-name 701
- 13.1.5.6 ip-address 702
- DHCP-SERVER-POLICY 13 - 31 703
- 13.1.5.7 netbios-name-server 703
- 13.1.5.8 netbios-node-type 704
- DHCP-SERVER-POLICY 13 - 33 705
- 13.1.5.9 next-server 705
- 13.1.5.10 no 706
- DHCP-SERVER-POLICY 13 - 35 707
- 13.1.5.11 option 707
- 13.1.5.12 respond-via-unicast 708
- DHCP-SERVER-POLICY 13 - 37 709
- 13.1.5.13 static-route 709
- 13.1.6 option 710
- 13.1.7 no 711
- 13.1.8 ping 712
- 13.1.9 dhcp-class 713
- 13.1.10 dhcp-class-mode 714
- DHCP-SERVER-POLICY 13 - 43 715
- 13.1.10.1 multiple-user-class 715
- 13.1.10.2 no 716
- DHCP-SERVER-POLICY 13 - 45 717
- 13.1.10.3 option 717
- CHAPTER 14 FIREWALL-POLICY 719
- 14.1 firewall-policy 720
- 14.1.1 alg 721
- 14.1.2 clamp 722
- 14.1.3 dhcp-offer-convert 723
- 14.1.4 dns-snoop 724
- 14.1.5 firewall 725
- 14.1.6 flow 726
- FIREWALL-POLICY 14 - 9 727
- 14.1.7 ip 728
- FIREWALL-POLICY 14 - 11 729
- FIREWALL-POLICY 14 - 13 731
- 14.1.8 ip-mac 732
- 14.1.9 logging 733
- 14.1.10 no 734
- 14.1.11 proxy-arp 735
- 14.1.13 storm-control 737
- [arp 738
- FIREWALL-POLICY 14 - 21 739
- CHAPTER 15 IGMP-SNOOP-POLICY 741
- 15.1 igmp-snoop-policy 742
- 15.1.1 igmp-snooping 743
- 15.1.2 querier 744
- 15.1.3 robustness-variable 745
- 15.1.4 unknown-multicast-fwd 746
- 15.1.5 no 747
- CHAPTER 16 MINT-POLICY 749
- 16.1 mint-policy 750
- 16.1.1 level 751
- 16.1.2 mtu 752
- 16.1.3 re-join timeout 753
- 16.1.4 security-level 754
- 16.1.5 sign-unknown-device 755
- 16.1.6 udp 756
- 16.1.7 no 757
- CHAPTER 17 MANAGEMENT-POLICY 759
- 17.1 management-policy 760
- 17.1.1 aaa-login 761
- 17.1.2 banner 763
- 17.1.3 ftp 764
- MANAGEMENT-POLICY 17 - 7 765
- 17.1.4 http 766
- 17.1.5 https 767
- 17.1.6 idle-session-timeout 768
- 17.1.7 no 769
- 17.1.8 restrict-access 770
- 17.1.9 snmp-server 771
- MANAGEMENT-POLICY 17 - 15 773
- 17.1.10 ssh 774
- 17.1.11 telnet 775
- 17.1.12 user 776
- MANAGEMENT-POLICY 17 - 19 777
- CHAPTER 18 RADIUS-POLICY 779
- 18.1 radius-group 780
- 18.1.1 guest 781
- 18.1.2 policy 782
- RADIUS-POLICY 18 - 5 783
- 18.1.3 rate-limit 785
- 18.1.4 no 786
- 18.2 radius-server-policy 787
- 18.2.1 authentication 788
- 18.2.2 crl-check 789
- 18.2.4 ldap-server 791
- 18.2.5 local 793
- 18.2.6 nas 794
- 18.2.7 no 795
- 18.2.8 proxy 796
- 18.2.9 session-resumptionn 797
- 18.2.10 use 798
- 18.3 radius-user-pool-policy 799
- 18.3.1 user 800
- 18.3.2 no 801
- CHAPTER 19 RADIO-QOS-POLICY 803
- 19.1 radio-qos-policy 804
- 19.1.1 accelerated-multicast 805
- 19.1.2 admission-control 806
- RADIO-QOS-POLICY 19 - 5 807
- 19.1.3 no 808
- 19.1.4 wmm 809
- CHAPTER 20 ROLE-POLICY 811
- 20.1 role-policy 812
- 20.1.1 default-role 813
- 20.1.2 no 814
- 20.1.3 user-role 815
- 20.1.3.1 ap-location 816
- ROLE-POLICY 20 - 7 817
- 20.1.3.2 authentication-type 817
- 20.1.3.3 captive-portal 818
- ROLE-POLICY 20 - 9 819
- 20.1.3.4 encryption-type 819
- 20.1.3.5 group 820
- ROLE-POLICY 20 - 11 821
- 20.1.3.6 mu-mac 821
- 20.1.3.7 no 822
- ROLE-POLICY 20 - 13 823
- 20.1.3.8 ssid 823
- 20.1.3.9 use 824
- CHAPTER 21 SMART-RF-POLICY 825
- 21.1 smart-rf-policy 826
- 21.1.1 assignable-power 827
- 21.1.2 auto-assign-sensor 828
- 21.1.3 channel-list 829
- 21.1.4 channel-width 830
- 21.1.5 coverage-hole-recovery 831
- 21.1.6 enable 832
- 21.1.7 group-by 833
- 21.1.8 interference-recovery 834
- 21.1.9 neighbor-recovery 835
- 21.1.10 no 836
- 21.1.11 sensitivity 837
- 21.1.12 smart-ocs-monitoring 838
- CHAPTER 22 WIPS-POLICY 839
- 22.1 wips-policy 840
- 22.1.1 ap-detection 841
- 22.1.2 enable 842
- 22.1.3 event 843
- WIPS-POLICY 22 - 7 845
- 22.1.5 no 847
- 22.1.6 use 848
- 22.1.7 signature 849
- WIPS-POLICY 22 - 13 851
- 22.1.7.1 bssid 851
- 22.1.7.2 dst-mac 852
- WIPS-POLICY 22 - 15 853
- 22.1.7.3 filter-ageout 853
- 22.1.7.4 frame-type 854
- WIPS-POLICY 22 - 17 855
- 22.1.7.5 mode 855
- 22.1.7.6 payload 856
- WIPS-POLICY 22 - 19 857
- 22.1.7.7 src-mac 857
- 22.1.7.8 ssid-match 858
- WIPS-POLICY 22 - 21 859
- 22.1.7.9 threshold-client 859
- 22.1.7.10 threshold-radio 860
- WIPS-POLICY 22 - 23 861
- 22.1.7.11 no 861
- CHAPTER 23 WLAN-QOS-POLICY 863
- 23.1 wlan-qos-policy 864
- 23.1.1 accelerated-multicast 865
- 23.1.2 classification 866
- WLAN-QOS-POLICY 23 - 5 867
- 23.1.3 multicast-mask 868
- 23.1.4 no 869
- 23.1.5 qos 870
- 23.1.6 rate-limit 871
- 23.1.7 svp-prioritization 873
- 23.1.8 voice-prioritization 874
- 23.1.9 wmm 875
- WLAN-QOS-POLICY 23 - 15 877
- CHAPTER 24 INTERFACE-RADIO 879
- 24.1 interface-radio Instance 881
- 24.1.1 aggregation 883
- 24.1.2 airtime-fairness 884
- 24.1.3 antenna-diversity 885
- 24.1.4 antenna-gain 886
- 24.1.5 antenna-mode 887
- 24.1.6 beacon 888
- 24.1.7 channel 889
- 24.1.8 data-rates 890
- 24.1.9 description 893
- 24.1.11 guard-interval 895
- 24.1.12 lock-rf-mode 896
- 24.1.13 max-clients 897
- 24.1.14 mesh 898
- 24.1.15 no 899
- 24.1.16 non-unicast 900
- 24.1.17 off-channel-scan 901
- 24.1.18 placement 902
- 24.1.19 power 903
- 24.1.20 preamble-short 904
- 24.1.21 probe-response 905
- 24.1.22 radio-share-mode 906
- 24.1.23 rf-mode 907
- 24.1.24 rifs 908
- 24.1.25 rts-threshold 909
- 24.1.26 shutdown 910
- 24.1.27 sniffer-redirect 911
- 24.1.28 use 912
- 24.1.29 wlan 913
- non-unicast queue bss 6 1 914
- non-unicast queue bss 7 1 914
- non-unicast queue bss 8 1 914
- 24.1.30 wireless-client 915
- CHAPTER 25 FIREWALL LOGGING 917
- FIREWALL LOGGING 25 - 3 919
- FIREWALL LOGGING 25 - 5 921
- 25.1.3 UDP packets log 922
- 25.1.4 ICMP type logs 923
- 25.1.5 ICMP type logs 924
- FIREWALL LOGGING 25 - 9 925
- 25.1.7 Raw IP Protocol logs 926
- 25.1.8 Firewall startup log 927
- 25.1.9 Manual time change log 928
- 25.1.10 Firewall ruleset log 929
- 25.1.11 TCP Reset Packets log 931
- 25.1.12 ICMP Destination log 932
- 25.1.13 ICMP Packet log 933
- 25.1.14 SSH connection log 934
- FIREWALL LOGGING 25 - 19 935
- Use Case 937
- Mototrola 938
- 26.1.1 Assumptions 939
- 26.1.2 Design 940
- •User Name: admin 942
- • Password: motorola 942
- 26.1.3.2 Creating a RF Domain 943
- Commit the Changes 945
- Creating an AP Profile 946
- WLAN_USECASE_01 950
Related products and manuals for Networking Motorola 2.1
Networking Motorola USB08 Specifications
(244 pages)
(244 pages)
Networking Motorola Droid 2 Life User Manual
(15 pages)
(15 pages)
(84 pages)
Networking Motorola Netopia 3300 User's Guide
(327 pages)
(327 pages)
Networking Motorola Netopia 2200 User's Guide
(351 pages)
(351 pages)
Networking Motorola SBG900 User Manual
(42 pages)
(42 pages)
Networking Motorola MPC5200 User Manual
(80 pages)
(80 pages)
Networking Motorola SB3100 User's Guide
(21 pages)
(21 pages)
Networking Motorola 2.1 User Manual
(713 pages)
(713 pages)
Networking Motorola MVME172 User Manual
(4 pages)
(4 pages)
© 2020, manymanuals.com. All rights reserved. | 1.335 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals