Motorola DSR-4530 Instruction Manual

Document No.: 523480-001DSR-4530 Commercial Integrated Receiver/Decoder Operator Guide

DSR-4530 5 2Connecting the DSR-4530Unpacking and Connecting the DSR-4530Cable connections described in this chapter, are made to the back panel of t

26 Figure 2-2: DSR-4530 Back Panel (Detailed)TVPass® CardETHERNETGIGE10/100AUX AUDIO IN PRIMARY AUDIO RELAY1ASYNC GND L+ L- GND R+ R- L+ L- GND R+ R-

DSR-4530 7 Connecting the DSR-4530Unpacking and MountingThe shipping carton contains the DSR-4530, two quick disconnect terminals, a power cord, and

28 4.To listen to audio during installation, connect the audio outputs to a local amplifier and speaker. A standard stereo system will suffice, but th

DSR-4530 9 3Operating the DSR-4530All operations described in this chapter require use of the front panel, as shown in Figure 3-1.Figure 3-1: DSR-4

310 Using the Front PanelThe front panel LCD screen displays a series of menus that can be used to configure and control the system. The name of the c

DSR-4530 11 Operating the DSR-4530Navigating the MenusEven though the keypad options shown on the LCD screen may change for each menu and for each f

312 How to Use the MenusAbout MenuThe front panel LCD displays the About menu when the DSR-4530 is initially plugged in or after a factory reset. This

DSR-4530 13 Operating the DSR-4530Overview of the LCD Panel Menu TreePressing the ENTER button when the cursor is on a menu name causes the cursor t

OPERATION PRECAUTIONSWARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.The lightning flash with the arrowhead

314

DSR-4530 15 Operating the DSR-4530

316 Installation MenusThe purpose of the installation menus is to configure the ports and choose settings that remain fixed over a period of time. The

DSR-4530 17 Operating the DSR-4530Input Field Default: Port 1Note: Unless changed, the DSR-4530 displays values for an L-band input on Port 1. The I

318 Xpnr Field Default: 1Note: This field is not available when the ASI In option in the Input field is selected. The Xpnr field cannot be edited if L

DSR-4530 19 Operating the DSR-4530Modulation MenuNote: This menu is not available when the ASI In option is selected. That option is located in the

320 Symbol/Code/Format Field Default: Mode-DependantNote: This field is not available when the DCII-Auto option in the Mode field is selected.The Symb

DSR-4530 21 Operating the DSR-4530Port 1 through Port 8 may be set up manually or automatically, and each individually. For manual setup, the user e

322 Port Config MenuUse this menu to configure LNB power for port 1.Port Test FieldThis function is currently not supported at this time.Port1 Power F

DSR-4530 23 Operating the DSR-4530AudioMix Field Default: StereoNote: If the audio input mode is stereo and you are connecting to a mono modulator,

DSR-4530 iChapter 1 Introducing the DSR-4530 ...

324 Audio1 Gain and Audio2 Gain MenusThese menus allow adjustment of the audio signal output level from 0 to -20dB in 1dB increments. Press the 56 but

DSR-4530 25 Operating the DSR-4530Subcarrier MenuThe Subcarrier menu is used to define standard settings used for processing an analog (non DigiCiph

326 Trigger Field Default: AutoThe Trigger field allows the user to select the trigger condition to activate an alarm on the IRD. When the alarm is ac

DSR-4530 27 Operating the DSR-4530Test Field Default: OffNote: The Test field returns to the default value (Off) when the field is exited.The Test f

328 Reset MenuThe Reset menu allows the user to reset the unit to the factory default settings or perform a power cycle. Press the 56 buttons until th

DSR-4530 29 Operating the DSR-4530Press any arrow button (3456) to back out of the field and leave it unchanged. Otherwise, press the ENTER button t

330 Video Out Format MenuThe Video Out Format menu allows the user to configure the video format. Press the 56 buttons until the Video Out Format menu

DSR-4530 31 Operating the DSR-4530Aspect Ratio MenuThe Aspect Ratio Menu displays the current input aspect ratio and has one field that allows the o

332 Firmware MenuThe Firmware menu displays the DSR-4530's firmware release information, which is equivalent to the product version number. This

DSR-4530 33 Operating the DSR-4530File FieldThe File field consists of two subfields:• Subfield #1 is editable and selects, by index, a download fil

TOCii Current Field... 33Rcvd F

334 Channel MenusTo access the Channel menus, press ENTER button to return to the main top-level menu (shown below). Press the 34 buttons until the cu

DSR-4530 35 Operating the DSR-4530Chnl FieldThe Chnl (Channel) field allows selection of the virtual channel for the output service. Channels that e

336 channel. This message is not displayed if the DSR-4530 was not already acquired to a virtual channel (e.g., when setting up the DSR-4530 for futur

DSR-4530 37 Operating the DSR-4530MPEG Select MenuThis menu allows the user to select which service is displayed at the video and audio outputs by s

338 Aud1Lang, Aud2Lang MenusThese menus (Audio1 and Audio2 Language) have three fields that allow the user to modify and view the status of the langua

DSR-4530 39 Operating the DSR-4530Press the ENTER button to confirm the selection.Left and Right Fields Default: DefNote: These fields operate in co

340 • If the AudioMix option (described on page 23) is set to Dual Mono and a language pair is not available that matches the user’s choice for Left a

DSR-4530 41 Operating the DSR-4530Text Lang MenuThis Text Language menu has two fields that allow the user to modify and view the status of the lang

342 Checking Status of ChannelOnce a channel is set up, the user can verify the status of the channel. To do this, access the Status Display menus by

DSR-4530 43 Operating the DSR-4530IP MenusUse the IP menus is to configure the 10/100 port. To access the IP menus, press ENTER button to return to

DSR-4530 iiiMemory Field ... 52

344 Press the ENTER button to confirm the selection and exit the field.Subnet Mask MenuUse the following procedure to set and view the Subnet Mask IP

DSR-4530 45 Operating the DSR-4530GigE MenusUse the GigE menus is to configure the GigE port. To access the GigE menus, press ENTER button to return

346 GigE Subnet Mask MenuUse the following procedure to set and view the GigE Subnet address (range: 000.000.000.000 to 255.255.255.255) for the upper

DSR-4530 47 Operating the DSR-4530GigE MPTS Address MenuUse the following procedure to set and view the GigE Single Program Transport Stream (SPTS)

348 Status Display MenusNote: Some of the status screens are not displayed when the active signal is received from a source other than the L-band inpu

DSR-4530 49 Operating the DSR-4530Status2 MenuNote: This menu is not displayed when the active signal is received from a source other than an L-band

350 Status4 MenuNote: This menu is not displayed when the active signal is received from a source other than an L-band input connector.Press the 56 bu

DSR-4530 51 Operating the DSR-4530Format FieldNote: This field is excluded from the the status display screen when the acquisition selection mode is

352 Status6 MenuPress the 56 buttons until the Status6 menu appears (shown below). This screen displays the DSR-4530’s Memory (free memory) and Flash

DSR-4530 53 Operating the DSR-4530Diagnostics MenusThe DSR-4530's diagnostic menus allow the user to isolate problems to the DSR-4530 or the sa

354 Clear Cntrs FieldNote: If a diagnostic menu other than Off is selected, the Clear Cntrs (clear counters) field also appears. This field is primari

DSR-4530 55 Operating the DSR-4530Audio Test Signal MenuThis menu allows the user to select an audio test signal for each of the two audio outputs,

356 Video Test Signal MenuA full-field video test signal is available that allows the user to display different test patterns by selecting the Pattern

DSR-4530 57 Operating the DSR-4530VITS MenuThis menu allows the user to insert Vertical Interval Test Signal (VITS) on lines 17 or 18. Press the 56

358 Field Field Default: 1Note: The IRD does not display this field when the waveform is set to Transmitted or Disabled.The Field field allows the use

DSR-4530 59 Operating the DSR-4530Cue Tone Field Default: OffThe Cue Tone (Signal) field lets the user turn the cue tone test ON and OFF. Press the

DSR-4530 61 4TroubleshootingBefore contacting the Hotline, review Table 4-1 for problems and suggested solutions.Table 4-1: Troubleshooting Solutio

DSR-4530 63 5Downlink/L-band FrequencyConversion TablesNote: A distributor or programmer can provide the latest C-band and Ku-band frequency plans a

DSR-4530 1 1Introducing the DSR-4530The Motorola DSR-4530 (Phase 2) is a commercial Integrated Receiver Decoder (IRD) designed for cable operators a

DSR-4530 65 6Product SupportIf You Need HelpFor assistance with Motorola products only, contact the Motorola Technical Response Center (TRC), 24 hour

DSR-4530 67 7Language AbbreviationsNote: This list of languages was recommended to system operators as the appropriate identifiers for audio, subtit

768 Irish iri Philippine (Other) phiItalian ita Polish polPanjabi pan Portuguese porJapanese jpn Rajasthani rajJavanese jav Romanian rumKashmiri kas R

DSR-4410MD 69 8DiagnosticsIntroductionThe Fast Fact Diagnostic Diagnostic screens (1 through 5) are a part of the IRD firmware created during product

870 Viewing the Fast Fact Diagnostic ScreensThe diagnostic screens (Figure 9-1 ) are available via the On-Screen Display (OSD) video out using a video

DSR-4410MD 71 DiagnosticsFast Facts ScreensThe Fast Facts screens are used as a method of viewing information and diagnostic data associated with the

872 VCT ID Shows the current VCT ID.Encryption Displays the current program’s encryption status.Service Displays the service number for the current pr

DSR-4410MD 73 DiagnosticsFast Facts 2The Fast Facts 2 screen displays information relating to the port configuration of the IRD.Field Name Definition

12 • Bypass video and audio inputs enable connections of analog signals to pass through the unit and switch on or off when an alarm is triggered.• Aud

874 Fast Facts 3The Fast Facts 3 screen displays information relating to video information.Field Name DefinitionVideo Locked An indication of video lo

DSR-4410MD 75 DiagnosticsFilm Mode Indication of if Film Mode is active or inactive.Aspect Ratio The aspect ratio of the video within the transport s

876 Fast Facts 4The Fast Facts 4 screen displays information relating to audio information. There are two columns of information displayed, one column

DSR-4410MD 77 DiagnosticsFast Facts 5 (10/100 Network)The Fast Facts 5 screen displays information relating to the Ethernet port (lower RJ-45 port on

878 Fast Facts 5 (Gigabit Ethernet)The Fast Facts 5 (Gigabit Ethernet) screen displays information relating to Gigabit Ethernet port (upper RJ-45 port

DSR-4530 79 9DSR-4530 Specifications RFInput Frequency Range 950 to 2150 MHzInput RF Level -25 to -65 dBmRF Port Impedance 75 OhmsRF Port Return

980 Note: Audio and data connectors may be ordered through Phoenix Contact part numbers 1840447 / 1840528. Transmission StandardDigiCipher Symbol Rat

DSR-4530 81 DSR-4530 SpecificationsConnectorsRF In F-type (Qty 8)AUX Video In BNC (Qty 1)Video Out BNC (Qty 1)OSD Video Out BNC (Qty 1)Alarm Screw

Caring for the Environment by Recycling When you see this symbol on a Motorola pdo not dispose of the product with residentiacommercial waste. roduct,

DSR-4530 3 Introducing the DSR-4530Disaster RecoveryThe DSR-4530 performs automatic disaster recovery of lost L-band signal without operator interve

523174-002 MGBI 04/05 Var rädd om miljön genom återvinning När du ser den här symbolen på en av Motorolas produkter ska du inte kasta produkten tills

6450 Sequence Dr.San Diego, CA 92121Document No: 523480-001, Rev. C523480- 001- 99D