Motorola CPCI-6115 Service Manual download pdf (Page 92)

CPCI-6115 CompactPCI Single Board Computer Installation and Use (6806800A68D)

Transition Module Preparation and Installation Block Diagram

5.2 Block Diagram

The block diagram for the CPCI-6115-MCPTM is shown in the following figure.

Figure 5-1 CPCI-6115-MCPTM Block Diagram

COM1

Compact

Flash 1

RS232

Transceiver

SROM

(Data)

User I/O J5 Connector User I/O J3 Connector

IOMX Function

(Data)

Primary IDE

(Control)

16:8 Mux

10/100/1000TX

PMC2 I/O Module PMC1 I/O Module

REAR PANEL

1 2 ... 87 88 89 90 91 92 93 94 95 96 97 ... 137 138

CPCI-6115 CompactPCI 1
Single Board Computer 1
Trademarks 2
Contents 3
List of Tables 10
List of Figures 11
About this Manual 13
Abbreviations 14
Conventions 16
Summary of Changes 17
Comments and Suggestions 18
Safety Notes 19
Operation 20
Installation 20
Cabling and Connectors 21
Environment 22
Sicherheitshinweise 23
Schaltereinstellungen/Jumper 24
Kabel und Stecker 26
Umweltschutz 26
Batterie 26
Introduction 27
1.2 Standard Compliances 28
1.3 Ordering Information 29
2.1 Overview 31
Requirements 32
2.3.2 Power Requirements 34
2.3.3 Thermal Requirements 34
2.4 Getting Started 37
2.5 Baseboard Preparation 38
2.5.3 J6, Bus Mode Selection 40
2.5.7 J20, Safe Start Header 42
2.6 Operating Modes 44
2.7 Installing Hardware 44
Procedure 45
Personal Injury or Death 46
2.9 Applying Power 49
3.1 Overview 51
3.2 Board Layout 52
3.4 ABORT/Reset Switch 54
3.5.7 CompactPCI Connector 58
PCI_RSVD = PCI Reserved pin 62
3.5.14 Safe Start Header 67
3.5.15 Bus Mode Select Header 67
3.5.18 +/-12 V Present Header 68
Functional Description 69
4.2 Block Diagram 70
4.3 General Description 71
4.3.2 Processor 72
4.3.3 L3 Cache 72
4.3.4.12 Interrupt Controller 76
4.3.4.13 PCI Bus Arbitration 76
4.3.4.14 Board Reset Logic 77
4.3.5 System Memory 81
4.3.6 Flash Memory 82
4.3.8 TL16C550C UART Devices 83
4.3.9 System Registers 83
4.3.10 Serial EEPROM Devices 83
4.3.11 PCI Bus 0.0 83
4.3.12 PCI Bus 1.0 83
4.3.13 IDE Controller 84
4.3.15 CompactPCI Bus 84
4.3.16 PMC Slots 84
4.4 Miscellaneous 86
4.4.3 Onboard Power Supplies 89
4.4.4 Hot Swap Support 89
4.4.5 Hot Swap Process 89
5.2 Block Diagram 92
5.4 Rear Panel Connectors 94
5.5.2.1 Host IO Connectors 96
5.5.2.2 PMC I/O Connectors 98
5.6 Jumper Settings 104
5.7 Functional Description 105
5.7.3 Hot-Swap Support 106
5.7.4 Serial EEPROM 106
5.7.5 PMC I/O Modules 106
5.7.7 PMC I/O Module 110
5.7.9 PMC I/O Connector 112
5.7.10 Host I/O Connector 112
5.8 Installing the PIM 113
Figure 5-9 Installing the PIM 114
Remote Start via the PCI Bus 117
MOTLoad Firmware 119
7.4 MOTLoad Commands 120
7.6 MOTLoad Tests 120
7.7 Using MOTLoad 121
7.7.2 Command Line Help 122
7.7.3 Command Line Rules 122
7.8 MOTLoad Command List 123
Memory Maps 127
8.2.2 Processor Memory Map 128
8.2.3 Default PCI Memory Map 129
8.2.5 System I/O Memory Map 131
8.2.7 CompactPCI Memory Map 131
8.2.9 L1, L2 and L3 Cache 132
8.2.10 System Memory 132
A Related Documentation 133
A.3 Related Specifications 134

Comments to this Manuals

No comments

Motorola CPCI-6115 Service Manual Page 92

Comments to this Manuals

Related products and manuals for Network switches Motorola CPCI-6115