Motorola CPCI-6115 Service Manual Page 39
- Page / 138
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Setting Switches and Jumpers Hardware Preparation and Installation
CPCI-6115 CompactPCI Single Board Computer Installation and Use (6806800A68D)
37
2.5.2 Setting Switches and Jumpers
Figure 2-2 on page 35 illustrates the placement of the switches, jumper headers, connectors
and LED indicators on the CPCI-6115. Use this figure to help identify the approximate location
of the jumpers on the CPCI-6115. There are seven manually configured headers on the
baseboard. They are described in the following table:
Table 2-5 CPCI-6115 Jumper Map
Reference Function Comment
J6 Bus Mode Select
Header
Jumper pins 1-2 for 60x mode
Jumper pins 2-3 for MPX mode
J9 Stand-Alone Operation
Header
Jumper pins 1-2 for Stand-Alone operation (no CPCI bus)
J10 Flash Boot Bank Select
Header
No jumper or jumper pins 1-2 for Bank A (32 MB)
Jumper pins 2-3 for Bank B (8 MB)
J15 +/-12 V Present Header Jumper pins 1-2 allows board operation without +/- 12 V
power
J20 Safe Start ENV Header No jumper or jumper pins 1-2 for normal ENV settings
Jumper pins 2-3 for safe ENV settings
J25 SROM Initialization
Enable Header
Jumper pins 1-2 to enable SROM init
No jumper or jumper pins 2-3 to disable SROM init
J99 Flash Bank A Write
Protect Header
Jumper pins 1-2 to enable Bank A Flash Write
No jumper to disable Flash Writes
SW2 Manual Geographic
Address -
OFF (default) - GA from CompactPCI backplane
ON - generate address locally
Damage of the Product
Setting/resetting the switches during operation can cause damage of the product.
Check and change switch settings before you install the product.
- CPCI-6115 CompactPCI 1
- Single Board Computer 1
- Trademarks 2
- Contents 3
- List of Tables 10
- List of Figures 11
- About this Manual 13
- Abbreviations 14
- Conventions 16
- Summary of Changes 17
- Comments and Suggestions 18
- Safety Notes 19
- Operation 20
- Installation 20
- Cabling and Connectors 21
- Environment 22
- Sicherheitshinweise 23
- Schaltereinstellungen/Jumper 24
- Kabel und Stecker 26
- Umweltschutz 26
- Batterie 26
- Introduction 27
- 1.2 Standard Compliances 28
- 1.3 Ordering Information 29
- 2.1 Overview 31
- Requirements 32
- 2.3.2 Power Requirements 34
- 2.3.3 Thermal Requirements 34
- 2.4 Getting Started 37
- 2.5 Baseboard Preparation 38
- 2.5.3 J6, Bus Mode Selection 40
- 2.5.7 J20, Safe Start Header 42
- 2.6 Operating Modes 44
- 2.7 Installing Hardware 44
- Procedure 45
- Personal Injury or Death 46
- 2.9 Applying Power 49
- 3.1 Overview 51
- 3.2 Board Layout 52
- 3.4 ABORT/Reset Switch 54
- 3.5.7 CompactPCI Connector 58
- PCI_RSVD = PCI Reserved pin 62
- 3.5.14 Safe Start Header 67
- 3.5.15 Bus Mode Select Header 67
- 3.5.18 +/-12 V Present Header 68
- Functional Description 69
- 4.2 Block Diagram 70
- 4.3 General Description 71
- 4.3.2 Processor 72
- 4.3.3 L3 Cache 72
- 4.3.4.12 Interrupt Controller 76
- 4.3.4.13 PCI Bus Arbitration 76
- 4.3.4.14 Board Reset Logic 77
- 4.3.5 System Memory 81
- 4.3.6 Flash Memory 82
- 4.3.8 TL16C550C UART Devices 83
- 4.3.9 System Registers 83
- 4.3.10 Serial EEPROM Devices 83
- 4.3.11 PCI Bus 0.0 83
- 4.3.12 PCI Bus 1.0 83
- 4.3.13 IDE Controller 84
- 4.3.15 CompactPCI Bus 84
- 4.3.16 PMC Slots 84
- 4.4 Miscellaneous 86
- 4.4.3 Onboard Power Supplies 89
- 4.4.4 Hot Swap Support 89
- 4.4.5 Hot Swap Process 89
- 5.2 Block Diagram 92
- 5.4 Rear Panel Connectors 94
- 5.5.2.1 Host IO Connectors 96
- 5.5.2.2 PMC I/O Connectors 98
- 5.6 Jumper Settings 104
- 5.7 Functional Description 105
- 5.7.3 Hot-Swap Support 106
- 5.7.4 Serial EEPROM 106
- 5.7.5 PMC I/O Modules 106
- 5.7.7 PMC I/O Module 110
- 5.7.9 PMC I/O Connector 112
- 5.7.10 Host I/O Connector 112
- 5.8 Installing the PIM 113
- Figure 5-9 Installing the PIM 114
- Remote Start via the PCI Bus 117
- MOTLoad Firmware 119
- 7.4 MOTLoad Commands 120
- 7.6 MOTLoad Tests 120
- 7.7 Using MOTLoad 121
- 7.7.2 Command Line Help 122
- 7.7.3 Command Line Rules 122
- 7.8 MOTLoad Command List 123
- Memory Maps 127
- 8.2.2 Processor Memory Map 128
- 8.2.3 Default PCI Memory Map 129
- 8.2.5 System I/O Memory Map 131
- 8.2.7 CompactPCI Memory Map 131
- 8.2.9 L1, L2 and L3 Cache 132
- 8.2.10 System Memory 132
- A Related Documentation 133
- A.3 Related Specifications 134
Related products and manuals for Network switches Motorola CPCI-6115
Network switches Motorola T1/E1 User Manual
(25 pages)
(25 pages)
Network switches Motorola T1/E1 Specifications
(122 pages)
(122 pages)
(31 pages)© 2020, manymanuals.com. All rights reserved. | 1.104 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals