Motorola ColdFire MCF5282 User Manual Page 72
- Page / 104
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
3-30 M5282EVB User’s Manual
PRELIMINARY—SUBJECT TO CHANGE WITHOUT NOTICE
Commands
SET Set Configurations
Usage:SET <option value>
The SET command allows the setting of user-configurable options within dBUG. With no
arguments, SET displays the options and values available. The SHOW command displays the
settings in the appropriate format. The standard set of options is listed below.
baud - This is the baud rate for the first serial port on the board. All communications between
dBUG and the user occur using either 9600 or 19200 bps, eight data bits, no parity, and one stop
bit, 8N1, with no flow control.
base - This is the default radix for use in converting a number from its ASCII text representation
to the internal quantity used by dBUG. The default is hexadecimal (base 16), and other choices are
binary (base 2), octal (base 8), and decimal (base 10).
client - This is the network Internet Protocol (IP) address of the board. For network
communications, the client IP is required to be set to a unique value, usually assigned by your local
network administrator.
server - This is the network IP address of the machine which contains files accessible via TFTP.
Your local network administrator will have this information and can assist in properly configuring
a TFTP server if one does not exist.
gateway - This is the network IP address of the gateway for your local subnetwork. If the client IP
address and server IP address are not on the same subnetwork, then this option must be properly
set. Your local network administrator will have this information.
netmask - This is the network address mask to determine if use of a gateway is required. This field
must be properly set. Your local network administrator will have this information.
filename - This is the default filename to be used for network download if no name is provided to
the DN command.
filetype - This is the default file type to be used for network download if no type is provided to the
DN command. Valid values are: “srecord”, “coff”, and “elf”.
mac - This is the ethernet Media Access Control (MAC) address (a.k.a hardware address) for the
evaluation board. This should be set to a unique value, and the most significant nibble should
always be even.
Examples:
To set the baud rate of the board to be 19200, the command is:
set baud 19200
NOTE
See the SHOW command for a display containing the correct
formatting of these options.
- M5282EVB User's Manual 1
- Contents 5
- MOTOROLA Tables v 9
- ILLUSTRATIONS 11
- Chapter 1 13
- 1-2 M5282EVB User’s Manual 14
- 1.1 MCF5282 Microprocessor 15
- 1-4 M5282EVB User’s Manual 16
- MCF5282 Microprocessor 16
- Chapter 1. M5282EVB 1-5 17
- 1.2 System Memory 18
- 1.2.6 M5282EVB Memory Map 19
- 1.3 Support Logic 20
- Chapter 1. M5282EVB 1-9 21
- Support Logic 21
- 1.3.2 Clock Circuitry 22
- 1.3.3 Watchdog Timer 22
- 1.3.4 Exception Sources 23
- 1.3.5 TA Generation 23
- 1.4 Communication Ports 24
- 1.4.2 FlexCAN 2.0 B Port 25
- 1.4.3 10/100T Ethernet Port 26
- 1.4.4 BDM/JTAG Port 26
- 1.4.5 I 27
- 1.4.6 QSPI 28
- 1.5.1 Expansion Connectors 28
- Table 1-18. J6 29
- Table 1-19. J7 29
- Table 1-17. J5 29
- Table 1-20. J2 30
- 1.5.3 Reset Switch (S2) 31
- 1.5.4 User LEDs 32
- 1.5.5 Other LEDs 32
- 1.7 Software Development 33
- 1-22 M5282EVB User’s Manual 34
- Software Development 34
- 2.1 System Configuration 35
- 6 - 12 V 36
- Input Power 36
- RS-232 Terminal 36
- 2.2 Installation and Setup 37
- 2-4 M5282EVB User’s Manual 38
- Installation and Setup 38
- Figure 2-3. Jumper Locations 40
- 2.4 Using The BDM Port 41
- 2-8 M5282EVB User’s Manual 42
- Using The BDM Port 42
- Chapter 3 43
- 3.2 Operational Procedure 44
- 3.2.2 System Initialization 45
- 3.3 Command Line Usage 46
- 3.4 Commands 47
- 3-6 M5282EVB User’s Manual 48
- Commands 48
- ASM Assembler 49
- BC Block Compare 50
- BF Block Fill 51
- BM Block Move 52
- BR Breakpoints 53
- BS Block Search 54
- DC Data Conversion 55
- DI Disassemble 56
- DL Download Console 57
- DN Download Network 58
- GO Execute 59
- GT Execute To 60
- IRD Internal Register Display 61
- IRM Internal Register Modify 62
- HELP Help 63
- LR Loop Read 64
- LW Loop Write 65
- MD Memory Display 66
- MM Memory Modify 67
- MMAP Memory Map Display 68
- RD Register Display 69
- RM Register Modify 70
- SET Set Configurations 72
- SHOW Show Configurations 73
- STEP Step Over 74
- SYMBOL Symbol Name Management 75
- TRACE Trace Into 76
- UPDBUG Update dBUG 77
- UPUSER Update User Flash 78
- 3.5 TRAP #15 Functions 79
- 3.5.2 IN_CHAR 80
- 3.5.3 CHAR_PRESENT 80
- 3.5.4 EXIT_TO_dBUG 81
- 3-40 M5282EVB User’s Manual 82
- TRAP #15 Functions 82
- Appendix A 83
- Configuring dBUG for Network 83
- Downloads 83
- Appendix B 87
- Schematics 87
- Fire®Cold MCF5282 88
- Evaluation Board - M5282EVB 88
- CAN Bus Connector 89
- - 9 way D-type (Female) 89
- Cold Fire® 90
- SDRAM Upper 16-bit Word 99
- SDRAM Lower 16-bit Word 99
- RS232 Transceiver 100
- NOT POPULATED AT ASSEMBLY 100
- Appendix C 101
- Evaluation Board BOM 101
Related products and manuals for Networking Motorola ColdFire MCF5282
Networking Motorola SB3100 User Manual
(119 pages)
(119 pages)
Networking Motorola MC9S12GC-Family User Manual
(136 pages)
(136 pages)
Networking Motorola MSC8101 ADS User Manual
(51 pages)
(51 pages)
Networking Motorola 2.1 User Manual
(9 pages)
(9 pages)
Networking Motorola PRM240 i User Manual
(2 pages)
(2 pages)
Networking Motorola T2-2500 User Manual
(15 pages)
(15 pages)
Networking Motorola SB6182 User's Guide
(2 pages)
(2 pages)
Networking Motorola VT1000v User's Guide
(32 pages)
(32 pages)
Networking Motorola i500plus User Manual
(6 pages)
(6 pages)
© 2020, manymanuals.com. All rights reserved. | 1.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals