Motorola ColdFire MCF5282 User Manual Page 37
- Page / 104
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 2. Initialization and Setup 2-3
PRELIMINARY—SUBJECT TO CHANGE WITHOUT NOTICE
Installation and Setup
2.2 Installation and Setup
The following sections describe all the steps needed to prepare the board for operation. Please read
the following sections carefully before using the board. When you are preparing the board for the
first time, be sure to check that all jumpers are in the default locations. Default jumper markings
are documented on the master jumper table and printed on the underside of the board. After the
board is functional in its default mode, the Ethernet interface may be used by following the
instructions provided in Appendix A.
2.2.1 Unpacking
Unpack the computer board from its shipping box. Save the box for storing or reshipping. Refer to
the following list and verify that all the items are present. You should have received:
• M5282EVB Single Board Computer
• M5282EVB User's Manual (this document)
• One RS232 communication cable
• One BDM (Background Debug Mode) “wiggler” cable
• MCF5282UM ColdFire Integrated Microprocessor User Manual
• ColdFire® Programmers Reference Manual
• A selection of Third Party Developer Tools and Literature
NOTE
Avoid touching the MOS devices. Static discharge can and will
damage these devices.
Once you have verified that all the items are present, remove the board from its protective jacket
and anti-static bag. Check the board for any visible damage. Ensure that there are no broken,
damaged, or missing parts. If you have not received all the items listed above or they are damaged,
please contact Matrix Design immediately - for contact details please see the front of this manual.
2.2.2 Preparing the Board for Use
The board, as shipped, is ready to be connected to a terminal and power supply without any need
for modification. Figure XXXX - shows the position of the jumpers and connectors.
2.2.3 Providing Power to the Board
The board accepts two means of power supply connection, either P2 or P3. Connector P2 is a
2.1mm power jack, P3 a lever actuated connector. The board accepts +6V to +12V DC at 1.0 Amp
via either of the connectors.
Table 2-1. Power Supply Connections on P2
Contact number Voltage
1Ground
2N/C
3 (Center) +6V to +12V DC
- M5282EVB User's Manual 1
- Contents 5
- MOTOROLA Tables v 9
- ILLUSTRATIONS 11
- Chapter 1 13
- 1-2 M5282EVB User’s Manual 14
- 1.1 MCF5282 Microprocessor 15
- 1-4 M5282EVB User’s Manual 16
- MCF5282 Microprocessor 16
- Chapter 1. M5282EVB 1-5 17
- 1.2 System Memory 18
- 1.2.6 M5282EVB Memory Map 19
- 1.3 Support Logic 20
- Chapter 1. M5282EVB 1-9 21
- Support Logic 21
- 1.3.2 Clock Circuitry 22
- 1.3.3 Watchdog Timer 22
- 1.3.4 Exception Sources 23
- 1.3.5 TA Generation 23
- 1.4 Communication Ports 24
- 1.4.2 FlexCAN 2.0 B Port 25
- 1.4.3 10/100T Ethernet Port 26
- 1.4.4 BDM/JTAG Port 26
- 1.4.5 I 27
- 1.4.6 QSPI 28
- 1.5.1 Expansion Connectors 28
- Table 1-18. J6 29
- Table 1-19. J7 29
- Table 1-17. J5 29
- Table 1-20. J2 30
- 1.5.3 Reset Switch (S2) 31
- 1.5.4 User LEDs 32
- 1.5.5 Other LEDs 32
- 1.7 Software Development 33
- 1-22 M5282EVB User’s Manual 34
- Software Development 34
- 2.1 System Configuration 35
- 6 - 12 V 36
- Input Power 36
- RS-232 Terminal 36
- 2.2 Installation and Setup 37
- 2-4 M5282EVB User’s Manual 38
- Installation and Setup 38
- Figure 2-3. Jumper Locations 40
- 2.4 Using The BDM Port 41
- 2-8 M5282EVB User’s Manual 42
- Using The BDM Port 42
- Chapter 3 43
- 3.2 Operational Procedure 44
- 3.2.2 System Initialization 45
- 3.3 Command Line Usage 46
- 3.4 Commands 47
- 3-6 M5282EVB User’s Manual 48
- Commands 48
- ASM Assembler 49
- BC Block Compare 50
- BF Block Fill 51
- BM Block Move 52
- BR Breakpoints 53
- BS Block Search 54
- DC Data Conversion 55
- DI Disassemble 56
- DL Download Console 57
- DN Download Network 58
- GO Execute 59
- GT Execute To 60
- IRD Internal Register Display 61
- IRM Internal Register Modify 62
- HELP Help 63
- LR Loop Read 64
- LW Loop Write 65
- MD Memory Display 66
- MM Memory Modify 67
- MMAP Memory Map Display 68
- RD Register Display 69
- RM Register Modify 70
- SET Set Configurations 72
- SHOW Show Configurations 73
- STEP Step Over 74
- SYMBOL Symbol Name Management 75
- TRACE Trace Into 76
- UPDBUG Update dBUG 77
- UPUSER Update User Flash 78
- 3.5 TRAP #15 Functions 79
- 3.5.2 IN_CHAR 80
- 3.5.3 CHAR_PRESENT 80
- 3.5.4 EXIT_TO_dBUG 81
- 3-40 M5282EVB User’s Manual 82
- TRAP #15 Functions 82
- Appendix A 83
- Configuring dBUG for Network 83
- Downloads 83
- Appendix B 87
- Schematics 87
- Fire®Cold MCF5282 88
- Evaluation Board - M5282EVB 88
- CAN Bus Connector 89
- - 9 way D-type (Female) 89
- Cold Fire® 90
- SDRAM Upper 16-bit Word 99
- SDRAM Lower 16-bit Word 99
- RS232 Transceiver 100
- NOT POPULATED AT ASSEMBLY 100
- Appendix C 101
- Evaluation Board BOM 101
Related products and manuals for Networking Motorola ColdFire MCF5282
Networking Motorola SB3100 User Manual
(119 pages)
(119 pages)
Networking Motorola MC9S12GC-Family User Manual
(136 pages)
(136 pages)
Networking Motorola MSC8101 ADS User Manual
(51 pages)
(51 pages)
Networking Motorola 2.1 User Manual
(9 pages)
(9 pages)
Networking Motorola PRM240 i User Manual
(2 pages)
(2 pages)
Networking Motorola T2-2500 User Manual
(15 pages)
(15 pages)
Networking Motorola SB6182 User's Guide
(2 pages)
(2 pages)
Networking Motorola VT1000v User's Guide
(32 pages)
(32 pages)
Networking Motorola i500plus User Manual
(6 pages)
(6 pages)
© 2020, manymanuals.com. All rights reserved. | 0.893 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals