SB6120-1.0.2.4-SCM01 Customer Release Notes
Motorola 365-095-13135
Sheet 11 of 20 Printed Copies of this Document are Not Controlled Revision X.2
9.3. 1.0.1.9-SCM00 (Not Released to General Availability)
9.3.1. Features
• No new features added in this release.
9.3.2. Defects Fixed
• Resolved an issue where an attached CPE device does not respond to a ping for some time after the
SB6120 has completed registration with a Cisco CMTS in 8-8-8 Bonded Mode. (cqvds00015193)
• Fixed a situation where an SB6120’s telnet/ping traffic stops due to a DSID sequence number
being out of range. (cqvds00015495)
9.4. 1.0.1.8-SCM02
9.4.1. Features
• The SB6120 can be configured to accept DCC init-tech values 1, 2, 3, and 4 when the modem is
registered in DOCSIS 3.0 Bonded Mode. For support of this feature, a new MIB object
(cmConfigDCCUpstreamDSBonded) was developed. (cqvds00014305)
)
cmConfigDCCUpstreamDSBonded
◦ Note: When setting this value to True(1), DCC init-tech level(s) 1,2,3, and 4 can be used to
shift only the upstream when the modem is in Downstream Bonded Mode. Setting
this value to False(2), prevents the SB6120 from acting upon DCC init-tech level(s)
1,2,3, and 4 when the modem is downstream bonded mode
9.4.2. Defects Fixed
• Resolved an intermittent issue where the SB6120 could not transmit RTPS Packets (causing a drop
of voice packets in the upstream direction). (cqvds00014640)
• Resolved an issue where UCD changes issued to the SB6120 connected to a CMTS utilizing
Modulation Agility may cause the SB6120 to eventually T4. (cqvds00015123)
• Restored support for the MIB Objects; cmRegularUserName and cmRegularUserPassword to
control user control to the SB6120 Password Protected GUI. (cqvds00014881)
• The SB6120 inaccurately reports the values for ifInOctets and ifOutOctets on the Ethernet and
HFC interfaces. (cqvds00014643)
• Fixed an issue where the SB6120 stayed Online with the CMTS but lost its IP Stack. The SB6120
could reboot at various intervals between 2 and 10 hours. (cqvds00014484)
• Fixed an issue where the SB6120 would fail to reinitialize the MAC Layer Processor after a DHCP
Renew failure if no ToD Server is present in the DHCP response. (cqvds00014811)
• When the modem processes an MDD Timeout, that action will now be logged to the GUI as well
as the docsDevEvText MIB Object. (cqvds00014864)
• Resolved an issue where a UCD change when equalization is on may cause the SB6120 to corrupt
upstream bursts - leading to data loss, T3 timeouts, and eventually T4 timeouts. (cqvds00014970)
• After the loss of a downstream channel (channel shutdown for maintenance), the SB6120 could get
stuck in init(o) when running BPI+. (cqvds00014190)
• The SB6120 will now accurately report the Hardware Version. Previous firmware was hardcoded
to report Hardware Revision 1.0. (cqvds00014699)
• Fixed and issue where the SB6120E running in Worldwide Mode fails a downstream DCC from
Annex-B to Annex-A. (cqvds00014012)
• MDD Timeouts were increased to prevent the SB6120 from resetting on a CMTS switchover due
to loss of MDD messages on the secondary channels. (cqvds00014391)
9.5. 1.0.1.7-SCM00
9.5.1. Features
• No new features added in this release.
Comments to this Manuals