SB6120-1.0.2.4-SCM01 Customer Release Notes
Motorola 365-095-13135
Sheet 9 of 20 Printed Copies of this Document are Not Controlled Revision X.2
◦ cmTestFtpTransferPayloadBytes <Payload data bytes transferred>
◦ cmTestFtpTransferTotalBytes <Total data and control Bytes>
◦ cmTestFtpTransferElapsedTime <Transfer elapsed time>
◦ cmTestFtpTransferThroughput <Calculated throughput>
• The following features and enhancements were inherited through the incorporation of the latest TI
Reference Code Release 1.2.3.
)
TurboDOX™ support <see cqvds00011632>
)
LinkUp and LinkDown traps <see cqvds00012562>
)
Dynamic SAID support
)
DOCSIS Path Verify (DPV) support
)
Complete DOCSIS 3.0 implementation of CM-STATUS messaging
)
US-SG-RES support
)
SNMP Write-Access Control (TLV10) support
)
Packet Processor Filter Match Counters
• Enhanced support of packet forwarding filters per DOCSIS 3.0 MULPI Specification.
(cqvds00012633)
• Added support for the TurboDOX™ bandwidth optimization feature. (cqvds00011632)
• New log messages were added for Partial Service Fallback and Recovery modes. (cqvds00014796)
)
cmConfigPartialServiceAction set to DOCSIS2.0 (Partial Service Fallback Mode)
• Loss of any Secondary channel at the CMTS Event Log Message:
“DS: Partial Service Fallback: MDD Lost: CM in DOCSIS 2.0 Recovery mode”
• Restoration of the lost/disconnected Secondary Channel Event Log Message:
“DS: Partial Service Recovery: CM in DOCSIS 3.0 mode”
)
cmConfigPartialServiceAction set to DOCSIS3.0 (Partial Service Recovery Mode)
• Loss of any Secondary channel at the CMTS Event Log Message:
“DS: Partial Service Fallback: MDD Lost: CM in DOCSIS 3.0 Recovery mode”
• Restoration of the lost/disconnected Primary or Secondary Channel Event Log Message:
“MDD Recovery following MDD loss”
• In response to customer requests, the SB6120 can now be configured to support pre-DOCSIS 3.0
default SNMP Access modes. For support of this feature, a new MIB object
(cmConfigDefaultSnmpAccess) was developed. (cqvds00015156)
)
cmConfigDefaultSnmpAccess
◦ Note: Setting this object to docsis30(0) disables SNMP access to the CM by Default unless
the modem receives a configuration file with the proper NmAccess Settings as
required in DOCSIS 3.0.
Setting this object to docsis20(1) enables SNMP access to the CM by Default. A
TLV55 or TLV11 entry for docsDevNmAccessInterface in the config file will
override this MIB object setting.
• When the SB6120 receives a Cable Modem Configuration file with a MISSING or INVALID
CVC, there is no LOG message posted to indicate the failure. The SB6120 Log Messages have
been enhanced to add more details of the error. (cqvds13967)
)
[WARNING] [DOCSIS.SWDL(pid=258)]: SW DL is disabled!
)
[WARNING] [DOCSIS.SWDL(pid=258)]: Reason: Missing or Invalid CVC!
• Enhanced the recovery mechanism of the SB6120 when changing from an S-CDMA upstream to
an A-TDMA upstream frequency. (cqvds00015154)
)
Originally fixed in cqvds00012668.
• Added support for the cmCarrierFrequencyOffset MIB. (cqvds00016178)
(21 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals