Motorola CPCI-6115 Service Manual Page 74
- Page / 196
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Functional Description
CPCI-6200 Installation and Use (6806800J66C)
74
4.3.4 I
2
C Bus 3
Bus 3 is connected between the IPMI controller and the following onboard I
2
C devices:
ADT7461 temperature sensor
64 KB user EEPROM
64 KB FRU/SDR EEPROM
64 KB SEL EEPROM used for system event log data
4.3.5 I
2
C Bus 4
Bus 4 is connected between the IPMI controller, processor, J5 connector and the following
onboard I
2
C devices:
8KB VPD EEPROM
Two 64 KB EEPROM for user configuration data storage
M41T83 Real Time Clock
SPD EEPROMs of DDR3 (on DIMM modules)
The I
2
C interface is routed to the J5 connector to provide access to the serial EEPROM located
on the rear transition module.
4.3.6 I
2
C Bus 5
Bus 5 is connected between the IPMI controller and processor providing intercommunication
between the two. There is no onboard I
2
C device on this bus.
4.4 System Memory
The MPC8572 includes two memory controllers, which operate in asynchronous mode i.e., the
DDR3 clocks are derived from a separate external clock oscillator.
This board supports one bank of memory on each controller, using either 1 GB or 2 GB DDR3
SODIMM. This provides memory configurations of 2 and 4 GB. This board also supports
memory speeds of up to 400 MHz.
- CPCI-6200 1
- Trademarks 2
- Contact Address 2
- Contents 3
- List of Tables 10
- List of Figures 13
- About this Manual 15
- Conventions 18
- Summary of Changes 19
- Introduction 21
- 1.2 Standard Compliances 24
- 1.3 Mechanical Data 26
- 1.4 Ordering Information 26
- 1.5 Product Identification 27
- Chapter 2 29
- 2.1 Overview 29
- 2.4 Power Requirements 31
- 2.5 Installing Accessories 32
- PMC Filler Plate 33
- PMC Alignment 33
- Voltage Key 33
- 2.6.3 Hardware Configuration 35
- 2.10 Factory-Installed Linux 42
- Chapter 3 45
- 3.1 Board Layout 45
- 3.2 Front Panel 46
- 3.3 Connectors and Headers 47
- 3.3.1 CPCI Bus Connector, J1 48
- 3.3.2 CPCI Bus Connector, J2 49
- 3.3.4 CPCI Connector, J4 51
- 3.3.7 Ethernet Connector 58
- 3.3.8 USB Connector 58
- 3.4 Switches 66
- 3.5 Front Panel LEDs 67
- 3.6 Status Indicators 68
- Functional Description 71
- 4.4 System Memory 74
- 4.5 Timers 75
- 4.6 Ethernet Interfaces 75
- 4.7 Local Bus Interface 75
- 4.7.3 Control and Timers PLD 77
- 4.8 DUART Interface 78
- 4.9 PCI Express Port 79
- 4.10 PCI/PCI-X Bus 80
- 4.11 Operation Modes 81
- 4.11.1 System Controller Mode 82
- 4.11.2 Peripheral Mode 82
- 4.11.3 Stand Alone Mode 83
- 4.12 PCI Express Expansion 84
- 4.13 System Interrupts 85
- 4.14 Clock Distribution 86
- 4.15 MPC8572 System Clock 87
- 4.16 Reset Control Logic 87
- 4.16.1 Abort/Reset Switch 89
- 4.16.2 Reset Timing 90
- 4.17 RTC Battery 91
- 4.18 IPMI Controller 91
- 4.19 Programmable Devices 93
- 4.19.1 Local Bus Control CPLD 94
- 4.19.2 Reset CPLD 94
- 4.19.3 CPCI Control CPLD 94
- 5.4 MOTLoad Commands 96
- 5.6 MOTLoad Tests 96
- 5.7 Using MOTLoad 97
- 5.7.2 Command Line Help 99
- 5.7.3 Command Line Rules 99
- 5.8 MOTLoad Command List 100
- MOTLoad Firmware 101
- Control via IPMI 107
- 6.1.3 IPMI Messaging Commands 108
- 6.1.4 SEL Device Commands 108
- 6.1.5 SDR Repository Commands 109
- 6.1.6 FRU Inventory Commands 109
- 6.1.7 Sensor Device Commands 110
- 6.2 PICMG 2.9 Commands 111
- 6.3 Emerson Specific Commands 112
- 6.3.2 OEM Commands 115
- 6.3.2.1 BMC/PM Change Role 116
- 6.4 FRU Information 118
- 6.5 Sensor Description 118
- Memory Maps and Addresses 137
- 7.2 CPCI-6200 Memory Map 138
- 7.4 System I/O Memory Map 140
- 7.4.1 System Status Register 143
- 7.4.2 System Control Register 144
- 7.4.5 Interrupt Register 1 148
- 7.4.6 Interrupt Register 2 149
- 7.4.7 Interrupt Mask Register 150
- 7.4.23 PLD Revision Register 167
- 7.4.24 PLD Date Code Register 168
- 7.4.25 Test Register 1 168
- 7.4.26 Test Register 2 169
- 7.4.27.2 Control Registers 170
- 7.4.27.3 Compare Registers 171
- 7.4.27.4 Counter Registers 172
- 7.5 Interrupt Controller 173
- C Device Addresses 174
- 7.7 PCI/PCI-X Configuration 175
- Replacing the Battery 179
- A.2 Replacing the Battery 180
- Related Documentation 181
- B.3 Related Specifications 183
- Safety Notes 185
- Installation 186
- Operation 187
- Hot Swap 188
- Sicherheitshinweise 189
- System Installation 191
- Batterie 192
- © 2009 Emerson Electric Co 196
Related products and manuals for Network switches Motorola CPCI-6115
(174 pages)
(31 pages)© 2020, manymanuals.com. All rights reserved. | 1.539 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals