Motorola DCP 501 User Manual Page 121
- Page / 141
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
112 Troubleshooting
DCP501 User Guide
Problem Possible Solution
There is no sound
or very little sound
from the speakers.
Check to make sure that each speaker has been properly connected to the
speaker output jacks on the rear panel of the DCP501.
Check that the speakers are working by utilizing the Test Tone function as
described in the “Operation” section.
Verify that the DCP501 has not been placed in MUTE mode.
Check that the volume control on the DCP501 has been adjusted to an
appropriate listening volume.
Verify that the DCP501 is set to the correct source (CATV, VCR, DVD, Tape,
etc).
If the front panel displays O V E R L O A D , one of two things has happened:
1 If the DCP501 detects the speakers have a short circuit, it shuts down
the amplifiers. Switch the DCP501 off, remove the short circuit, and turn
the DCP501 back on. The DCP501 should now work as normal. If
O V E R L O A D is still displayed, a short circuit condition remains.
2 If the maximum amplifier output power is exceeded, the DCP501 shuts
down the amplifiers. Turn down the volume a little and switch the
DCP501 off and then switch the DCP501 back on and the DCP501
should now work as normal. If O V E R L O A D is still displayed, turn the
volume down some more.
There is no sound
or very little sound
from the center
speaker.
Check that the center speaker has been properly connected to the DCP501.
Check that the speaker is working by utilizing the Test Tone function as
described in the “Operation” section.
The DCP501 may be set to Stereo mode. Select one of the surround sound
audio modes (Dolby Digital, Dolby Pro Logic II, dts) and listen for output.
Verify that the CENTER selection in the SPEAKER SETUP menu is not set to
NONE as defined in the “Operation” section.
Adjust the volume control of the DCP501 to an appropriate level.
There is no sound
or very little sound
from the surround
speakers.
Check that the surround speakers are properly connected to the DCP501.
Check that the speakers are working by utilizing the Test Tone function as
described in the “Operation” section.
The DCP501 may be set to Stereo mode. Select one of the surround sound
audio modes (Dolby Digital, Dolby Pro Logic II, dts) and listen for output.
Verify that the SURROUND selection in the SPEAKER SETUP menu is not set
to NONE as defined in the “Operation” section.
Adjust the volume control of the DCP501 to an appropriate level.
AUDIO
There is no sound
or very little sound
from a powered
subwoofer.
Verify that the subwoofer is properly connected as defined in the “Installation”
section.
Verify that the SUBWOOFER? setting in the SPEAKER SETUP menu is
configured as defined in the “Operation” section.
Verify that the subwoofer is properly connected to an AC outlet and powered
on as applicable.
Verify that the volume/gain control on the subwoofer is adjusted accordingly as
applicable.
- Home Theater System 1
- User Guide 1
- WARNING 2
- CAUTION 2
- REPAIRS 2
- EXAMPLE OF ANTENNA GROUNDING 2
- Important Safeguards 3
- Regulatory Information 4
- Declaration of Conformity 5
- Canadian Compliance 5
- FCC Part 68 Statement 5
- Notes on Copyright 6
- Contact Us 6
- Contents 7
- Contents iii 9
- Introduction 11
- Before You Begin 12
- Document Conventions 12
- Overview 13
- Supplied Accessories 15
- Disc Information 15
- Handling Discs 16
- Cleaning Discs 16
- Storing Discs 16
- Region Numbers 16
- Front Panel 17
- Item Control Description 18
- DCP501 Display 19
- 10 Overview 20
- Overview 11 21
- Rear Panel 22
- Overview 13 23
- Item Description 24
- Operating the Remote Control 25
- 16 Overview 26
- Overview 17 27
- 18 Overview 28
- Overview 19 29
- 20 Overview 30
- 2 Press the Cursor Up ∧ 31
- 22 Overview 32
- Installation 33
- Installing the DCP501 34
- Recording Your Connections 35
- Connecting Your TV 36
- Cable(s) you will need: 37
- Connecting to Cable TV 38
- Speaker Placement 39
- 4 Snap the tab closed 40
- Front speakers 41
- Subwoofer 41
- Surround speakers 43
- Connecting Your VCR 44
- S-Video 45
- (monaural) 48
- Alternate 49
- A/V Source 49
- Digital Audio Connections 50
- CONNECTORS 51
- To wall outlet 52
- FM antenna 52
- M antenna 52
- Connecting for Power 53
- VideoDigital Audio 54
- Operation 55
- Setting Up Audio 56
- Subwoofer and Speakers 59
- 20 Press SELECT or OK 63
- 51 Press SELECT or OK 70
- 53 Press SELECT or OK 70
- Test Tone Adjust 72
- 3 Press down arrow (∨ 73
- 11 Press SELECT or OK 76
- Advanced Audio Setup 77
- 4 Press SELECT or OK 78
- 8 Press down arrow (∨ 79
- Using Cable TV Record 84
- 3 Press SELECT or OK 85
- 2 Press down arrow (∨ 85
- 7 Press down arrow (∨ 86
- Using CATV Channel Scan 87
- 3 Press select or OK 88
- Using the DCP501 Tuner 90
- Sound Effects 91
- Resume Play 94
- Using the DVD Banner Display 95
- Operation 89 99
- CURSOR up/down (∧ 99
- Using the CD Banner Display 102
- Program Edit on a CD 104
- Using the Repeat Feature 106
- Random Play 107
- DCP501 User Guide 108
- DVD Setup 111
- Resetting Your Password 118
- DCP501 User Guide 119
- Troubleshooting 120
- Problem Possible Solution 121
- Specifications 125
- DVD/CD Player 126
- Input/Output 126
- General 127
- TV and VCR Setup Codes 128
- Manufacturer TV Setup Code 129
- VCR Setup Codes 132
- Manufacturer VCR Setup Code 133
- Language Codes 136
- Language 137
- Abbreviations and Acronyms 138
- 499892-001 141
© 2020, manymanuals.com. All rights reserved. | 0.139 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals