Motorola Symbol LS3578 User's Guide Page 161
- Page / 596
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Scanning 3 - 5
To scan a bar code, center the symbol in any orientation within the aiming pattern. Be sure the entire symbol is
within the rectangular area formed by the cross pattern.
Figure 3-3
Scanning Orientation with Imager Aiming Pattern
The device can also read a bar code presented within the aiming pattern but not centered. The top examples in
Figure 3-4 show acceptable aiming options, while the bottom examples can not be decoded.
Figure 3-4
Acceptable and Incorrect Aiming
1D bar code symbol
2D bar code symbol
2D dot peen DPM symbol
Aiming Pattern
NOTE Scanning Direct Part Mark (DPM) bar codes with the MT2070-DP scanner: Due to the reflective nature of
some surfaces used with DPM bar codes (see Figure 3-3), it may be necessary to tilt the scanner at an
angle relative to the target (Motorola recommends 25-45 degrees). For example, when scanning a 15 mil
dot peen Data Matrix bar code marked on an aluminum surface, present the target between two and three
inches from the nose of the scanner, and tilt the scanner at a 30 degree angle.
When scanning standard (non-DPM) bar codes with any configuration of the scanner, follow the standard
aiming instructions described in Aiming on page 3-4.
0123 45
0123 45
0123 45
0123 45
- MT2070/MT2090 1
- User Guide 3
- Warranty 4
- Revision History 5
- Table of Contents 7
- Table of Contents ix 9
- Table of Contents xi 11
- Table of Contents xiii 13
- Table of Contents xv 15
- Table of Contents xvii 17
- Table of Contents xix 19
- Table of Contents xxi 21
- About This Guide 23
- Device Configurations 24
- Cradle Configurations 24
- About This Guide xxi 25
- Chapter Descriptions 26
- Notational Conventions 27
- Related Documents 28
- Service Information 28
- Chapter 1 Getting Started 29
- Accessories 30
- Features 31
- Cradle Features 32
- Single Slot - Back View 33
- Single Slot - Mounting Cups 34
- Getting Started 1 - 7 35
- Four Slot - Back View 36
- Getting Started 1 - 9 37
- Host Interfaces 38
- Out-of-Box Startup 38
- Insert the Battery 39
- Connect the Cradle 39
- Supplying Power to the Cradle 40
- Configure the Device 41
- Battery Charging 42
- Battery Safety 43
- Radio Communications 44
- Resetting the Device 45
- Waking the Device 45
- Battery Removal 46
- Spare Battery Charging 46
- Screen Protector 46
- Getting Started 1 - 19 47
- MT2070/MT2090 Keypad 50
- Keypad Functionality 51
- F2, 2, A, B, C, a, b, c 52
- Table 2-1 53
- Entering Information 56
- Screen Icons 57
- Table 2-2 58
- Home Screen 59
- Figure 2-3 60
- Table 2-3 60
- User Settings 61
- Figure 2-6 62
- Figure 2-7 62
- Device Status 63
- Battery Status 63
- About Screen 64
- Scan Item 65
- Figure 2-12 66
- Figure 2-13 66
- Transmit: Separate 66
- Transmit: Together 66
- About 67
- Scan Inventory 68
- Quantity 69
- View Inventory Menu 70
- Figure 2-19 71
- Figure 2-20 71
- Save Inventory 72
- Figure 2-23 73
- Simple Inventory 74
- Transmit 75
- View Inventory 75
- Figure 2-28 77
- Figure 2-29 77
- Figure 2-30 78
- Figure 2-31 78
- Scan-To-IP 80
- Terminal Host Setup Screen 81
- Figure 2-36 82
- Figure 2-37 83
- Figure 2-38 83
- Scan Transmit 84
- View Data 86
- Delete Last 86
- Preview On 87
- Figure 2-46 88
- Figure 2-47 89
- Figure 2-48 89
- MT2070 MT2090 89
- Find WLANs 90
- Manage Profiles 90
- Creating a New Profile 91
- Profile ID 92
- Profile Name 92
- Operating Mode 92
- Figure 2-53 94
- Table 2-6 94
- Security Mode 95
- Authentication Type 97
- Tunneled Authentication 97
- Table 2-9 98
- User Certificate Selection 99
- User Certificate Installation 100
- Server Certificate Selection 102
- User Name 103
- Password 104
- Advanced Identity 105
- Credential Cache Options 106
- Encryption 108
- Table 2-12 109
- Table 2-11 109
- Hexadecimal Keys 110
- Pass-phrase Dialog 111
- IP Address Entry 113
- Figure 2-80 114
- Table 2-14 114
- Table 2-15 114
- Transmit Power 115
- Battery Usage 116
- Manage Certificates 117
- Figure 2-85 118
- Figure 2-86 118
- Certificate Properties 119
- Import a Certificate 119
- Delete a Certificate 120
- Manage PACs 121
- PAC Properties 122
- Delete PAC 122
- Import PAC 122
- Figure 2-96 123
- Figure 2-97 123
- Figure 2-98 124
- Table 2-19 124
- Regulatory Options 125
- Band Selection 125
- System Options 126
- Auto PAC Settings 126
- Change Password 127
- Wireless Status 130
- Signal Strength 131
- Current Profile 131
- Figure 2-109 132
- Table 2-24 132
- Table 2-25 132
- IPv4 Status 133
- Wireless Log 134
- Wireless Diagnostics 135
- Figure 2-114 136
- Trace Route 137
- Figure 2-117 138
- Table 2-27 138
- Log On/Off 139
- Enable/Disable Radio 140
- Settings 141
- Rapid Deployment 142
- MSP Agent 142
- BTExplorer 143
- Add a Bluetooth Service 145
- Turn Bluetooth On/Off 147
- Security Tab 148
- Discovery Tab 148
- Figure 2-136 149
- Figure 2-137 149
- Configure USB 150
- Table 2-29 151
- Utilities 152
- Task Manager 153
- Resetting the MT20X0 154
- Waking the MT20X0 155
- Chapter 3 Scanning 157
- Table 3-1 158
- LED Definitions 159
- Scanning in Hand-Held Mode 160
- Scanning 3 - 5 161
- Laser Aiming 162
- Scanning in Presentation Mode 163
- Scanning Considerations 164
- Decode Distances 165
- Table 3-5 166
- Table 3-6 166
- Introduction 167
- Table 4-1 168
- Wireless Beeper Definitions 169
- Radio Communications 4 - 5 171
- Bluetooth 172
- Technology Profile Support 172
- *General Discoverable Mode 173
- HID Host Parameters 174
- Radio Communications 4 - 9 175
- *No Delay (0 msec) 176
- *Disable Keypad Emulation 177
- *Disable Function Key Mapping 178
- *Disable Simulated Caps Lock 179
- *No Case Conversion 179
- Auto-reconnect Feature 180
- Reconnect Attempt Interval 181
- Radio Communications 4 - 17 183
- Out of Range Indicator 184
- MT20X0(s) To Cradle Support 185
- *Unlocked Pairing Mode 187
- Pairing Methods 188
- Unpairing 188
- Pairing Bar Code Format 189
- Considerations 190
- Radio Communications 4 - 25 191
- Bluetooth Security 192
- PIN Code 193
- Scanner Options 195
- Scanning Sequence Examples 196
- Errors While Scanning 196
- Table 5-1 197
- User Preferences 198
- Host Mode 199
- Parameter # F1h A4h 199
- Decode Pager Motor Enable 200
- Parameter # F1h 65h 200
- *Enable Adaptive Scanning 201
- *Beep After Good Decode 202
- *Medium Tone 203
- *High Volume 204
- *Standard (Level) 205
- *Disabled Always 206
- Parameter # 89h 207
- Parameter # F0h, 32h 207
- *Enable Decoding Illumination 208
- Batch Mode 209
- Parameter # F1 20h 209
- Batch Mode (continued) 210
- Parameter # 544 210
- * Disable FIPS Mode 211
- Miscellaneous Parameters 212
- Prefix/Suffix Values 213
- *Data As Is 214
- FN1 Substitution Values 215
- Key Category Parameter # 67h 215
- Decimal Value Parameter # 6Dh 215
- *Disable No Read 216
- Chapter 6 Imaging Preferences 217
- Imaging Preferences 6 - 3 219
- Imaging Preferences 220
- Image Capture Illumination 221
- Parameter # F0h 69h 221
- Snapshot Mode Timeout 222
- Parameter # F0h, 43h 222
- Snapshot Aiming Pattern 222
- Parameter # F0h, 2Ch 222
- *Disable Image Cropping 223
- Crop to Pixel Addresses 224
- Parameter # F0h 86h 225
- JPEG Quality and Size Value 225
- *JPEG File Format 226
- *Disable Signature Capture 227
- *JPEG Signature Format 228
- Imaging Preferences 6 - 13 229
- *Disable Video View Finder 230
- Customizing the MT20X0 7 - 3 233
- Navigator.xml File Content 234
- Customizing the MT20X0 7 - 5 235
- Chapter 8 RS-232 Interface 237
- RS-232 Parameter Defaults 239
- RS-232 Host Parameters 240
- RS-232 Interface 8 - 5 241
- RS-232 Host Types 242
- Baud Rate 243
- *Baud Rate 9600 244
- RS-232 Interface 8 - 9 245
- *1 Stop Bit 246
- *Check For Received Errors 247
- Standard RTS/CTS 248
- RTS/CTS Option 1 248
- RTS/CTS Option 2 248
- RTS/CTS Option 3 248
- Software Handshaking 249
- ACK/NAK with ENQ 250
- XON/XOFF 250
- *Minimum: 2 Sec 251
- *Host: Low RTS 252
- *Minimum: 0 msec 253
- *Normal Operation 254
- *Send Bar Code 254
- RS-232 Interface 8 - 19 255
- Table 8-4 256
- RS-232 Interface 8 - 21 257
- RS-232 Interface 8 - 23 259
- Chapter 9 USB Interface 261
- Connecting a USB Interface 262
- USB Parameter Defaults 263
- Table 9-1 264
- USB Host Parameters 265
- USB Device Type (continued) 266
- CDC COM Port Emulation 267
- Emulation device 268
- USB Interface 9 - 9 269
- *No Delay 270
- *Disable 272
- USB Interface 9 - 15 275
- * 8 msec 276
- * Disable 277
- ASCII Character Set for USB 279
- Table 9-2 280
- USB Interface 9 - 21 281
- USB Interface 9 - 23 283
- Table 9-3 284
- USB Interface 9 - 25 285
- Table 9-4 286
- USB Interface 9 - 27 287
- Table 9-6 288
- USB Interface 9 - 29 289
- IBM Parameter Defaults 293
- IBM 468X/469X Host Parameters 294
- Convert Unknown to Code 39 295
- Table 11-1 299
- Keyboard Wedge Host Types 300
- *North American 301
- *Disable Caps Lock On 305
- *Disable Caps Lock Override 305
- *No Convert 306
- Keyboard Maps 308
- Table 11-2 309
- Table 11-3 313
- Table 11-4 314
- Table 11-5 316
- Table 11-6 316
- Table 11-7 317
- Chapter 12 Symbologies 319
- Symbology Parameter Defaults 320
- Symbologies 12 - 3 321
- Table 12-1 322
- Symbologies 12 - 5 323
- *Enable UPC-A 325
- *Enable UPC-E 325
- *Disable UPC-E1 326
- *Enable EAN-8/JAN-8 326
- *Enable EAN-13/JAN-13 327
- * Disable Bookland EAN 327
- Parameter # 10h 328
- *Ignore Supplementals 329
- Parameter # 50h 331
- *Combined 332
- *Transmit UPC-A Check Digit 332
- *Transmit UPC-E Check Digit 333
- *Transmit UPC-E1 Check Digit 334
- UPC-E Preamble 335
- Parameter # 23h 335
- UPC-E1 Preamble 336
- Parameter # 24h 336
- Convert UPC-E to UPC-A 337
- Parameter # 25h 337
- Convert UPC-E1 to UPC-A 337
- Parameter # 26h 337
- *Disable EAN/JAN Zero Extend 338
- Bookland ISBN Format 339
- Parameter # F1h 40h 339
- UCC Coupon Extended Code 340
- Parameter # 55h 340
- Coupon Report 340
- Parameter # F1h DAh 340
- *New Coupon Symbols 341
- *Disable ISSN EAN 341
- Code 128 342
- Symbologies 12 - 25 343
- *Enable GS1-128 344
- *Enable ISBT 128 344
- *Disable ISBT Concatenation 345
- *Enable Check ISBT Table 346
- *Enable Code 39 347
- *Disable Trioptic Code 39 347
- *Disable Code 32 Prefix 348
- Set Lengths for Code 39 349
- *Disable Code 39 Check Digit 350
- *Disable Code 39 Full ASCII 351
- *Disable Code 93 352
- Symbologies 12 - 35 353
- *Disable Code 11 354
- Symbologies 12 - 37 355
- Interleaved 2 of 5 (ITF) 357
- Symbologies 12 - 41 359
- Discrete 2 of 5 (DTF) 361
- Symbologies 12 - 45 363
- Codabar (NW - 7) 364
- Symbologies 12 - 47 365
- *Disable CLSI Editing 366
- *Disable NOTIS Editing 366
- *Disable MSI 367
- *One MSI Check Digit 369
- Chinese 2 of 5 370
- Korean 3 of 5 371
- Inverse 1D 372
- Postal Codes 373
- *Disable UK Postal 374
- *Transmit UK Postal 375
- *Disable Japan Postal 375
- *Disable Australian Postal 376
- *Disable Netherlands KIX Code 376
- *Disable UPU FICS Postal 377
- GS1 DataBar 378
- *Disable GS1 DataBar Expanded 379
- *Security Level 3 380
- Composite 381
- *Disable TLC39 382
- *UPC Never Linked 382
- 2D Symbologies 383
- *Disable Code 128 Emulation 384
- *Enable Data Matrix 385
- *Enable Maxicode 385
- *Enable QR Code 386
- *Enable MicroQR 386
- *Enable Aztec 387
- Redundancy Level 388
- *Redundancy Level 1 389
- Security Level 390
- Report Version 391
- Chapter 13 Accessories 393
- Maintenance 394
- Batteries 394
- Mounting 394
- Single Slot Cradles 395
- Communication 396
- LED Indicators 397
- Four Slot Cradles 398
- Charging 399
- Four Slot Battery Charger 400
- Troubleshooting 402
- Using ADF Bar Codes 404
- ADF Bar Code Menu Example 404
- Rule 2: The UPC Scanning Rule 405
- Alternate Rule Sets 405
- ADF Bar Codes 407
- Table 14-1 408
- Special Commands 409
- Save Rule 410
- Quit Entering Rules 410
- Disable Rule Set 411
- Criteria 412
- Code Types (continued) 413
- Code Lengths 419
- Code Lengths (continued) 420
- Any Message OK 424
- Numeric Keypad 425
- Numeric Keypad (continued) 426
- Rule Belongs To Set 427
- Send Data 428
- Send Data (continued) 429
- Setup Field(s) 431
- Move Cursor 432
- Send Pause 432
- Skip Ahead 433
- Skip Back 434
- Skip Ahead (continued) 434
- Skip Back (continued) 435
- Send Preset Value 436
- Modify Data 437
- Pad Data with Spaces 438
- Pad Data with Zeros 442
- Control Characters 447
- Keyboard Characters 452
- Send ALT Characters 466
- Send Alt \ 470
- Send Alt ] 470
- Send Keypad Characters 471
- Send Function Key 476
- Send Function Key (continued) 477
- Send Right Control Key 483
- Turn On/Off Rule Sets 489
- Turn Off Rule Set 1 490
- Turn Off Rule Set 2 490
- Turn Off Rule Set 3 490
- Turn Off Rule Set 4 490
- Alphanumeric Keyboard 491
- Chapter 15 Maintenance and 505
- Table 15-1 508
- Table 15-2 511
- Table 15-3 512
- Table 15-4 513
- Table 15-5 515
- Four Slot Charge Only Cradle 516
- Table 15-7 517
- Table 15-8 518
- Table 15-9 519
- Table A-1 521
- Symbol Code Identifiers 531
- Table B-1 532
- AIM Code Identifiers 533
- ]C1AIMID 534
- Programming Reference B - 5 535
- Table B-3 536
- Programming Reference B - 7 537
- Appendix C Sample Bar Codes 539
- 3 456789 012340 540
- 1234 5670 540
- Trioptic Code 39 541
- Interleaved 2 of 5 542
- Data Matrix 543
- Maxicode 543
- US Postnet 544
- UK Postal 544
- Appendix D Numeric Bar Codes 545
- 4, 5, 6, 7 546
- Numeric Bar Codes D - 3 547
- Alphanumeric Bar Codes E - 3 551
- Alphanumeric Bar Codes E - 5 553
- Alphanumeric Bar Codes E - 7 555
- Alphanumeric Bar Codes E - 9 557
- Alphanumeric Bar Codes E - 11 559
- Alphanumeric Bar Codes E - 13 561
- Alphanumeric Bar Codes E - 15 563
- Alphanumeric Bar Codes E - 17 565
- Code Structure 567
- Capture Box 568
- Dimensions 569
- Data Format 569
- Additional Capabilities 570
- Signature Boxes 570
- Using Only a USB Cable 572
- Quick Startup Exercises G - 3 573
- Modifying the Startup Program 575
- Disabling Scanner Services 575
- ADCAPI_StopService() C API 576
- Numerics 577
- Index - 3 579
- Index - 5 581
- Index - 7 583
- Glossary 585
- Glossary - 3 587
- Glossary - 5 589
- Glossary - 7 591
- Tell Us What You Think 593
Related products and manuals for Bar code readers Motorola Symbol LS3578
(20 pages)
Bar code readers Motorola LS1203 Specifications
(202 pages)
(202 pages)
Bar code readers Motorola LI2208 Specifications
(416 pages)
(416 pages)
Bar code readers Motorola DS3508 Specifications
(386 pages)
(386 pages)
Bar code readers Motorola DS3508 Specifications
(316 pages)
(316 pages)
Bar code readers Motorola RS507 User Manual
(16 pages)
(16 pages)
(2 pages)
(36 pages)
Bar code readers Motorola MT2070 User's Guide
(560 pages)
(560 pages)
© 2020, manymanuals.com. All rights reserved. | 0.791 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals