Motorola LS2208-SR20001R Specifications Page 34
- Page / 392
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
2-8
LS 2208 Product Reference Guide
Scanning in Hands-Free Mode
The LS 2208 Intellistand adds greater flexibility to your scanning operation. Refer to
Assembling the Stand, Mounting the Stand (optional), and Scanning in the Hands-Free
Mode for detailed information about hands-free scanning.
Assembling the Stand
Figure 2-5. Assembling the Stand
Note:Before tightening the wingnut under the base, ensure that the flat
areas on the flexible neck fit securely in the grooves in the base.
Stand base
Wingnut
1. Unscrew the wingnut
from the bottom of the
one piece scanner
“cup”.
2. Fit the bottom of the
neck piece into the
opening on the top of
the stand base.
3. Tighten the wingnut
underneath the base
to secure the cup and
neck piece to the base
(see the note below).
4.Bend the neck to the
desired position for
scanning.
One piece scanner
“cup” with flexible neck.
Flat areas
- Product Reference Guide 1
- Contents 5
- Chapter 4. User Preferences 6
- Chapter 6. RS-232 Interface 7
- Chapter 7. USB Interface 7
- Chapter 11. 123Scan 8
- Chapter 12. Symbologies 9
- Appendix C. Sample Bar Codes 12
- Appendix D. Numeric Bar Codes 12
- Glossary 12
- Feedback 12
- About This Guide 13
- Notational Conventions 15
- Related Publications 15
- Service Information 15
- Symbol Support Center 16
- Business Partner for service 19
- Chapter 1 21
- Getting Started 21
- Unpacking Your Scanner 22
- Setting Up the Scanner 23
- Configuring Your Scanner 24
- Removing the Interface Cable 25
- Chapter 2 27
- Scanning 27
- Beeper Definitions 28
- LED Definitions 30
- Scanning in Hand-Held Mode 31
- Decode Zone 33
- Scanning in Hands-Free Mode 34
- Mounting the Stand (optional) 35
- Chapter 3 37
- Troubleshooting 38
- Technical Specifications 40
- Scanner Signal Descriptions 42
- Chapter 4 45
- User Preferences 45
- Beeper Tone 49
- *Medium Frequency 49
- Beeper Volume 50
- *High Volume 50
- Power Mode 51
- Laser On Time 52
- Beep After Good Decode 53
- *Beep After Good Decode 53
- Chapter 5 55
- Keyboard Wedge Interface 55
- Power supply 56
- (if needed) 56
- Keyboard Wedge Host Types 58
- *North American 59
- Keystroke Delay 63
- Intra-Keystroke Delay 64
- Caps Lock On 65
- *Disable Caps Lock On 65
- Caps Lock Override 66
- *Disable Caps Lock Override 66
- Convert Wedge Data 66
- *No Convert 67
- FN1 Substitution 68
- Send Make and Break 68
- Figure 5-3. IBM PC/XT 69
- Figure 5-4. IBM PC/AT 70
- Figure 5-5. NCR 7052 32-KEY 70
- Figure 5-6. NCR 7052 58-KEY 71
- Chapter 6 83
- RS-232 Interface 83
- *Baud Rate 9600 84
- RS-232 Default Parameters 85
- RS-232 Host Parameters 87
- RS-232 Host Types 89
- OPOS/JPOS 90
- Fujitsu RS-232 90
- Baud Rate 91
- Baud Rate (continued) 92
- Parity (continued) 94
- Stop Bit Select 95
- *1 Stop Bit 95
- Data Bits 95
- Check Receive Errors 96
- *Check For Received Errors 96
- Hardware Handshaking 97
- Standard RTS/CTS 98
- RTS/CTS Option 1 98
- RTS/CTS Option 2 98
- Software Handshaking 99
- ACK/NAK with ENQ 101
- XON/XOFF 101
- Host Serial Response Time-out 102
- *Minimum: 2 Sec 102
- RTS Line State 103
- *Host: Low RTS 103
- Beep on <BEL> 103
- *Minimum: 0 msec 104
- Intercharacter Delay 104
- Nixdorf Beep/LED Options 105
- Ignore Unknown Characters 106
- ASCII / Character Set 107
- Chapter 7 113
- USB Interface 113
- Connecting a USB Interface 114
- USB Default Parameters 116
- USB Host Parameters 117
- French Windows 118
- German Windows 118
- Spanish Windows 119
- Italian Windows 119
- French Canadian Windows 95/98 119
- Swedish Windows 120
- UK English Windows 120
- Japanese Windows (ASCII) 120
- Portuguese-Brazilian Windows 120
- USB Keystroke Delay 121
- *No Delay 121
- USB CAPS Lock Override 122
- USB Ignore Unknown Characters 123
- Emulate Keypad 124
- Function Key Mapping 125
- Simulated Caps Lock 125
- Convert Case 126
- ASCII Character Set 127
- Chapter 8 137
- IBM 468X/469X Interface 137
- Host Port Connector 138
- Interface cable 138
- IBM Default Parameters 139
- IBM 468X/469X Host Parameters 140
- Port Address (continued) 141
- Convert Unknown to Code 39 141
- Chapter 9 143
- Wand Emulation Interface 143
- Wand port 144
- Portable Data 144
- Terminal 144
- Wand Emulation Host Types 146
- Leading Margin (Quiet Zone) 147
- *80 msec 147
- Polarity 148
- *Bar High/Margin Low 148
- Chapter 10 151
- Host Port Connector 152
- Beep Style 155
- Parameter Pass-Through 156
- Convert Newer Code Types 157
- Module Width 158
- Code 39 Full ASCII Conversion 159
- Transmission Timeout 160
- Leading Margin 162
- Check For Decode LED 163
- Chapter 11 165
- 123Scan Parameter 166
- Chapter 12 167
- Symbologies 167
- Errors While Scanning 168
- Symbology Default Parameters 169
- Enable/Disable UPC-A/UPC-E 173
- *Enable UPC-A 173
- *Enable UPC-E 173
- Enable/Disable UPC-E1 174
- *Disable UPC-E1 174
- Enable/Disable EAN-13/EAN-8 175
- *Enable EAN-13 175
- *Enable EAN-8 175
- Enable/Disable Bookland EAN 176
- *Disable Bookland EAN 176
- *Ignore Supplementals 178
- *Transmit UPC-A Check Digit 180
- *Transmit UPC-E Check Digit 180
- Transmit UPC-E1 Check Digit 181
- UPC-A Preamble 182
- *System Character 182
- UPC-E Preamble 183
- UPC-E1 Preamble 184
- Convert UPC-E to UPC-A 185
- Convert UPC-E1 to UPC-A 186
- EAN-8/JAN-8 Extend 187
- *Disable EAN/JAN Zero Extend 187
- UPC/EAN Security Level 188
- *UPC/EAN Security Level 0 188
- UPC/EAN Security Level 2 189
- UPC/EAN Security Level 3 189
- UCC Coupon Extended Code 190
- Code 128 191
- Enable/Disable UCC/EAN-128 192
- *Enable UCC/EAN-128 192
- Enable/Disable Code 39 193
- *Enable Code 39 193
- *Disable Trioptic Code 39 194
- Convert Code 39 to Code 32 195
- Code 32 Prefix 196
- *Disable Code 32 Prefix 196
- Set Lengths for Code 39 197
- Code 39 - Length Within Range 198
- Code 39 - Any Length 198
- *Disable Code 39 Check Digit 199
- Transmit Code 39 Check Digit 200
- *Disable Code 39 Full ASCII 201
- *Do Not Buffer Code 39 202
- Buffer Data 203
- Clear Transmission Buffer 203
- Transmit Buffer 204
- • No transmission occurs 205
- • The buffer remains empty 205
- Enable/Disable Code 93 206
- *Disable Code 93 206
- Set Lengths for Code 93 207
- Code 93 - Length Within Range 208
- Code 93 - Any Length 208
- *Disable Code 11 209
- Set Lengths for Code 11 210
- Code 11 - Length Within Range 211
- Code 11 - Any Length 211
- *Disable 212
- Transmit Code 11 Check Digits 213
- Interleaved 2 of 5 (ITF) 214
- I 2 of 5 - Any Length 216
- Transmit I 2 of 5 Check Digit 218
- Convert I 2 of 5 to EAN-13 219
- Discrete 2 of 5 (DTF) 220
- D 2 of 5 - Any Length 222
- Chinese 2 of 5 223
- Codabar (NW - 7) 224
- Set Lengths for Codabar 225
- Codabar - Length Within Range 226
- Codabar - Any Length 226
- CLSI Editing 227
- *Disable CLSI Editing 227
- NOTIS Editing 228
- *Disable NOTIS Editing 228
- Enable/Disable MSI 229
- *Disable MSI 229
- Set Lengths for MSI 230
- MSI - Length Within Range 231
- MSI - Any Length 231
- MSI Check Digits 232
- *One MSI Check Digit 232
- Transmit MSI Check Digit(s) 233
- MSI Check Digit Algorithm 234
- *MOD 10/MOD 10 234
- RSS (Reduced Space Symbology) 235
- RSS (continued) 236
- *Disable RSS Limited 236
- *Disable RSS Expanded 236
- Convert RSS to UPC/EAN 237
- Redundancy Level 238
- Redundancy Level 2 239
- Redundancy Level 3 239
- Redundancy Level 4 240
- Security Level 241
- Security Level 2 242
- Security Level 3 242
- Bi-directional Redundancy 243
- Intercharacter Gap Size 244
- *Normal Intercharacter Gaps 244
- Chapter 13 245
- Miscellaneous Scanner Options 245
- Scanning Sequence Examples 246
- Transmit Code ID Character 248
- Prefix/Suffix Values 249
- Scan Data Transmission Format 250
- *Data As Is 251
- <DATA> <SUFFIX> 251
- <PREFIX> <DATA> 251
- Data Format Cancel 252
- FN1 Substitution Values 253
- Transmit “No Read” Message 254
- *Disable No Read 254
- Synapse Interface 255
- Chapter 14 257
- Advanced Data Formatting 257
- Using ADF Bar Codes 258
- ADF Bar Code Menu Example 259
- Rule 2: The UPC Scanning Rule 260
- Alternate Rule Sets 260
- Default Rules 263
- Special Commands 264
- Save Rule 265
- Quit Entering Rules 266
- Disable Rule Set 267
- Criteria 268
- Code Types (continued) 270
- Code Lengths 271
- Code Lengths (continued) 273
- Specific String at Start 276
- Any Message OK 277
- Numeric Keypad 278
- Rule Belongs To Set 279
- Send Data 280
- Send Data (continued) 282
- Setup Field(s) 284
- Move Cursor 285
- Send Pause 285
- Skip Ahead 286
- Skip Ahead (continued) 287
- Skip Back 288
- Skip Back (continued) 289
- Modify Data 290
- Remove All Spaces 291
- Crunch All Spaces 291
- Stop Space Removal 291
- Remove Leading Zeros 291
- Stop Zero Removal 291
- Pad Data with Spaces 293
- Pad Data with Zeros 297
- Beep Once 301
- Beep Twice 301
- Beep Three Times 301
- Characters) 302
- Keyboard Characters 306
- Send ALT Characters 318
- Send Keypad Characters 322
- Send Function Key 326
- Send Function Key (continued) 327
- Send Right Control Key 332
- Send GUI Y 338
- Send GUI Z 338
- Turn On/Off Rule Sets 339
- Alphanumeric Keyboard 340
- Appendix A 351
- Standard Default Parameters 351
- Appendix B 361
- Programming Reference 361
- Code Character Code Type 362
- AIM Code Identifiers 363
- ]C1AIMID 364
- Appendix C 367
- Sample Bar Codes 367
- UPC/EAN (continued) 368
- Interleaved 2 of 5 368
- RSS 14 on page 12-69) 369
- Appendix D 371
- Numeric Bar Codes 371
- Glossary-2 378
- Glossary-3 379
- Glossary-4 380
- Glossary-5 381
- Glossary-6 382
- Numerics 383
- Tell Us What You Think 389
- 72-58808-02 392
- Revision A — September 2003 392
Related products and manuals for Bar code readers Motorola LS2208-SR20001R
Bar code readers Motorola DS3508 Specifications
(386 pages)
(386 pages)
Bar code readers Motorola DS3508 Specifications
(316 pages)
(316 pages)
Bar code readers Motorola RS507 User Manual
(16 pages)
(16 pages)
(2 pages)
(36 pages)
Bar code readers Motorola MT2070 User's Guide
(560 pages)
(560 pages)
© 2020, manymanuals.com. All rights reserved. | 0.749 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals