Motorola RFS6000 - Wireless RF Switch User Manual Page 290
- Page / 948
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Motorola RF Switch CLI Reference Guide
5-34
access to the network. The IPSec tunnel is only between the client and the switch. After
that the packets on the trusted side are sent without encryption.
1. Create and configure a WLAN.
RFSwitch(config)#
RFSwitch(config)#wireless
RFSwitch(config-wireless)#wlan 2 enable
RFSwitch(config-wireless)#wlan 2 ssid MONARCH2
RFSwitch(config-wireless)#wlan 2 vlan 2
2. Create and configure DHCP.
RFSwitch(config)#ip dhcp pool vlan2
RFSwitch(config-dhcp)#address range 10.1.1.2 10.1.1.254
RFSwitch(config-dhcp)#default-router 10.1.1.1
RFSwitch(config-dhcp)#network 10.1.1.0/24
3. Create and configure a VLAN interface named vlan2.
RFSwitch(config)#interface vlan2
RFSwitch(config-if)#ip address 10.1.1.1/24
4. Create and configure another VLAN interface named vlan3.
RFSwitch(config)#interface vlan 3
RFSwitch(config-if)#ip address dhcp
Use the commands below to configure IPSec VPN on the switch:
1. Create an Extended ACL.
RFSwitch(config-ext-nacl)#ip access-list extended 101
2. Configure the local subnet and remote subnet as interesting traffic.
RFSwitch(config-ext-nacl)# permit ip 10.1.1.0/24 any
RFSwitch(config-ext-nacl)# permit ip 192.168.0.0/24 any
3. Configure a private pool address.
RFSwitch(config)# ip local pool lo 192.168.0.2 hi 192.168.0.10
4. Specify DNS/WINS for the remote client.
RFSwitch(config)#crypto isakmp client configuration group
default
NOTE: The example below is for a IPSec-L2TP connection over a mobile
unit. Use a windows default client for this configuration.
- Motorola RFS Series Wireless 1
- LAN Switches 1
- About This Guide 3
- Annotated Symbols 7
- Motorola Service Information 11
- General Information 12
- Motorola, Inc 13
- End-User License Agreement 13
- Contents 19
- Chapter 3. User Exec Commands 21
- Contents 23
- Chapter 22. ESPI Instance 33
- Chapter 23. RFID Instance 33
- Chapter 24. SOLE Instance 34
- Chapter 25. Smart RF Instance 34
- 1.1 CLI Overview 38
- Introduction 39
- Command Description 41
- 1.3.1 Basic Conventions 43
- 1.4.3 Deleting Entries 47
- Keystrokes Purpose 48
- 2.1.1 clrscr 50
- 2.1.2 exit 51
- 2.1.3 help 52
- 2.1.4 no 53
- – high temperature limit 58
- – low temperature limit 58
- – URL to which to copy 58
- Parameters (GLOBAL Config) 80
- 2.2 show 85
- Display 86
- 2.2.1 autoinstall 90
- 2.2.2 banner 91
- 2.2.4 crypto 93
- 2.2.6 history 97
- 2.2.7 interfaces 98
- 2.2.8 ip 100
- Common Commands 101
- Parameters 101
- 2.2.9 ldap 107
- 2.2.10 licenses 109
- 2.2.11 logging 110
- 2.2.12 mac 111
- 2.2.13 mac-address-table 112
- 2.2.14 management 113
- 2.2.15 mobility 114
- 2.2.16 ntp 117
- 2.2.17 port-channel 119
- 2.2.18 power 120
- 2.2.19 privilege 121
- 2.2.20 radius 122
- • RFS7000 123
- • RFS6000 123
- 2.2.22 redundancy -group 124
- 2.2.23 redundancy-history 127
- 2.2.24 redundancy -members 128
- 2.2.25 rtls 129
- 2.2.26 smtp-notification 132
- 2.2.27 snmp 134
- 2.2.28 snmp-server 135
- 2.2.30 static-channel-group 140
- 2.2.31 terminal 141
- 2.2.32 timezone 142
- 2.2.33 traffic-shape 143
- 2.2.34 users 144
- 2.2.35 version 145
- 2.2.36 wireless 146
- 2.2.37 wlan-acl 160
- 2.2.38 access-list 161
- 2.2.39 aclstats 162
- 2.2.40 alarm-log 163
- 2.2.41 boot 164
- 2.2.42 clock 165
- 2.2.43 debugging 166
- 2.2.44 dhcp 167
- 2.2.45 file 168
- 2.2.46 ftp 169
- 2.2.47 password-encryption 170
- 2.2.48 running-config 171
- 2.2.49 securitymgr 175
- 2.2.50 sessions 176
- 2.2.51 startup-config 177
- 2.2.52 upgrade-status 179
- 2.2.53 mac-name 180
- 2.2.54 access-list 181
- 2.2.55 aclstats 182
- 2.2.56 alarm-log 183
- RFSwitch#show alarm-log 1 184
- RFSwitch# 184
- 2.2.57 firewall 185
- 2.2.58 role 186
- User Exec Commands 187
- Command Description Ref 188
- 3.1.1 clear 189
- RFSwitch> 190
- 3.1.2 cluster-cli 191
- 3.1.3 debug 192
- Examples 193
- 3.1.5 enable 195
- 3.1.6 logout 196
- 3.1.7 page 197
- 3.1.8 ping 198
- 3.1.9 quit 199
- 3.1.10 telnet 200
- 3.1.11 terminal 201
- 3.1.12 traceroute 202
- Privileged Exec Commands 203
- 4.1.1 acknowledge 206
- 4.1.2 archive 207
- If Untar fails..? 208
- 4.1.3 cd 209
- 4.1.4 change-passwd 210
- 4.1.5 clear 211
- 4.1.6 clock 215
- 4.1.7 cluster-cli 216
- 4.1.8 configure 217
- 4.1.9 copy 218
- 4.1.10 debug 219
- – Debugs all default messages 220
- 4.1.11 delete 227
- 4.1.12 diff 228
- + policy vlan 44 229
- + policy wlan 10 229
- group kumar3 229
- 4.1.14 disable 231
- 4.1.15 edit 232
- 4.1.16 enable 233
- 4.1.17 erase 234
- 4.1.18 halt 235
- 4.1.19 kill 236
- 4.1.20 logout 237
- 4.1.21 mkdir 238
- 4.1.22 more 239
- 4.1.23 page 241
- 4.1.24 ping 242
- 4.1.25 pwd 243
- 4.1.26 quit 244
- 4.1.27 reload 245
- 4.1.28 rename 246
- 4.1.29 rmdir 247
- 4.1.30 telnet 248
- 4.1.31 terminal 249
- 4.1.33 upgrade 251
- 4.1.34 upgrade - abort 253
- 4.1.35 write 254
- Global Configuration Commands 257
- 5.1.1 aaa 261
- Usage Guidelines 262
- 5.1.3 autoinstall 270
- RFSwitch(config)# 271
- 5.1.4 banner 272
- 5.1.5 boot 273
- 5.1.6 bridge 274
- 1 vlan 2 276
- 5.1.7 country-code 277
- 5.1.8 crypto 278
- command is issued 287
- 5.1.9 do 295
- 5.1.10 end 296
- 5.1.11 errdisable 297
- 5.1.12 ftp 298
- 5.1.13 hostname 299
- 5.1.14 interface 300
- RFSwitch(config-if)# 301
- 5.1.15 ip 302
- 5.1.17 line 315
- 5.1.18 local 316
- 5.1.19 logging 317
- 5.1.20 mac 320
- 5.1.21 mac-address-table 321
- 5.1.22 mac-name 322
- 5.1.23 management 323
- 5.1.24 ntp 324
- 5.1.25 prompt 329
- 5.1.26 radius-server 330
- RFSwitch(config-radsrv)# 331
- 5.1.27 ratelimit 332
- 5.1.28 redundancy 333
- 5.1.29 role 336
- 5.1.31 service 339
- RFSwitch(config)#service dhcp 341
- 5.1.32 smtp-notification 342
- 5.1.33 snmp-server 350
- 5.1.34 spanning-tree 363
- (config-mst) instance 364
- RFSwitch(config-mst)# 366
- 5.1.35 timezone 367
- 5.1.36 traffic-shape 368
- 5.1.37 username 371
- 5.1.39 wireless 375
- 5.1.40 wlan-acl 376
- 5.1.41 network-element-id 379
- 5.1.42 firewall 380
- Crypto-isakmp Instance 383
- 6.1.1 authentication 385
- 6.1.2 clrscr 386
- 6.1.3 encryption 387
- 6.1.4 end 388
- 6.1.5 exit 389
- 6.1.7 hash 391
- 6.1.8 help 392
- 6.1.9 lifetime 393
- 6.1.10 no 394
- 6.1.11 service 395
- 6.1.12 show 397
- Crypto-group Instance 401
- 7.1.1 clrscr 403
- 7.1.2 dns 404
- 7.1.3 end 405
- 7.1.4 exit 406
- 7.1.5 help 407
- 7.1.6 service 408
- 7.1.7 show 409
- Crypto-peer Instance 413
- 8.1.1 clrscr 415
- 8.1.2 end 416
- 8.1.3 exit 417
- 8.1.4 help 418
- 8.1.5 no 419
- 8.1.6 service 420
- 8.1.7 set 421
- 8.1.8 show 422
- Crypto-ipsec Instance 425
- 9.1.1 end 427
- 9.1.2 exit 428
- 9.1.3 help 429
- 9.1.4 mode 430
- 9.1.5 no 431
- 9.1.6 show 432
- Crypto-map Instance 435
- 10.1.1 clrscr 437
- 10.1.2 end 438
- 10.1.3 exit 439
- 10.1.4 help 440
- 10.1.5 match 441
- 10.1.7 service 444
- [ipaddress 447
- <host name>] 447
- Crypto-trustpoint Instance 453
- 11.1.1 clrscr 455
- 11.1.2 company-name 456
- 11.1.3 email 457
- 11.1.4 end 458
- 11.1.5 exit 459
- 11.1.6 fqdn 460
- 11.1.7 help 461
- 11.1.8 ip-address 462
- 11.1.9 no 463
- 11.1.10 password 464
- 11.1.11 rsakeypair 465
- 11.1.12 service 466
- 11.1.13 show 467
- 11.1.14 subject-name 469
- Interface Instance 471
- 12.1.1 clrscr 473
- 12.1.2 crypto 474
- 12.1.3 description 475
- 12.1.4 duplex 476
- 12.1.5 end 477
- 12.1.6 exit 478
- 12.1.7 help 479
- 12.1.8 ip 480
- {secondary} 481
- <1-1000000> 481
- 12.1.9 mac 483
- 12.1.10 management 484
- 12.1.11 no 485
- 12.1.12 port-channel 486
- How src-dst-mac mode works 488
- How src-dst-ip mode works 488
- 12.1.13 power 489
- 12.1.14 service 491
- 12.1.15 show 492
- 12.1.17 spanning-tree 495
- 12.1.19 static-channel-group 499
- 12.1.20 switchport 500
- 12.1.21 storm-control 502
- Spanning tree-mst Instance 503
- instance configurations 504
- 13.1.1 clrscr 505
- 13.1.2 end 506
- 13.1.3 exit 507
- 13.1.4 help 508
- 13.1.5 instance 509
- 13.1.6 name 510
- 13.1.7 no 511
- 13.1.8 revision 512
- 13.1.9 service 513
- 13.1.10 show 515
- Extended ACL Instance 517
- 14.1.1 clrscr 519
- 14.1.2 deny 520
- 14.1.4 exit 527
- 14.1.5 help 528
- 14.1.6 mark 529
- RFSwitch(config-ext-nacl)# 533
- 14.1.7 no 535
- 14.1.8 permit 536
- 14.1.9 service 541
- 14.1.10 show 542
- Standard ACL Instance 545
- 15.1.1 clrscr 547
- 15.1.2 deny 548
- 15.1.3 end 550
- 15.1.4 exit 551
- 15.1.5 help 552
- 15.1.6 mark 553
- 15.1.8 permit 556
- 15.1.10 show 560
- Extended MAC ACL Instance 563
- 16.1.1 clrscr 565
- 16.1.2 deny 566
- 01:02:89:78:78:45 569
- 16.1.4 exit 571
- 16.1.5 help 572
- 16.1.6 mark 573
- 16.1.7 no 576
- 16.1.8 permit 577
- MAC address: 580
- 16.1.9 service 581
- 16.1.10 show 583
- DHCP Server Instance 587
- 17.1.1 address 590
- 17.1.2 bootfile 591
- 17.1.3 class 592
- 17.1.3.2 config-dhcp-class 593
- 11.22.33.56 594
- RFSwitch(config-dhcp-class)# 594
- 17.1.4 client-identifier 595
- 17.1.5 client-name 596
- 17.1.6 clrscr 597
- 17.1.7 ddns 598
- 17.1.8 default-router 600
- 17.1.9 dns-server 601
- 17.1.10 domain-name 602
- 17.1.11 end 603
- 17.1.12 exit 604
- 17.1.13 hardware-address 605
- 17.1.14 help 606
- 17.1.15 host 607
- 17.1.16 lease 608
- 17.1.17 netbios-name-server 610
- 17.1.18 netbios-node-type 611
- 17.1.19 network 612
- 17.1.20 next-server 613
- 17.1.21 no 614
- 17.1.22 option 615
- 17.1.23 service 616
- 17.1.24 show 617
- 17.1.25 update 619
- 17.1.26 unitcast-enable 620
- 17.2.2 Creating a Host Pool 623
- 17.2.4 Creating a DHCP Option 626
- DHCP Class Instance 627
- 18.1.1 clrscr 629
- 18.1.3 exit 631
- 18.1.4 help 632
- 18.1.5 multiple-user-class 633
- 18.1.6 no 634
- 18.1.7 option 635
- 18.1.9 show 638
- Radius Server Instance 641
- 19.1.1 authentication 643
- 19.1.2 ca 645
- 19.1.3 clrscr 646
- 19.1.4 crl-check 647
- 19.1.5 end 648
- 19.1.6 exit 649
- 19.1.7.1 clrscr 651
- 19.1.7.2 end 651
- 19.1.7.3 exit 651
- 19.1.7.4 group 652
- 19.1.7.5 guest-group 652
- 19.1.7.6 help 653
- 19.1.7.7 no 654
- 19.1.7.8 policy 655
- 19.1.7.11 service 658
- 19.1.7.12 show 659
- 19.1.8 help 663
- 19.1.9 ldap-server 664
- Name:-%{User-Name}}) 665
- 19.1.10 nas 667
- 19.1.11 no 668
- 19.1.12 proxy 669
- 19.1.13 rad-user 671
- 19.1.15 service 675
- 19.1.16 show 676
- Wireless Instance 679
- 20.1.1 aap 683
- RFSwitch(config-wireless)# 684
- 20.1.2 admission-control 685
- 20.1.3 adopt-unconf-radio 686
- 20.1.4 adoption-pref-id 687
- 20.1.5 ap 688
- Floor SalesUnit 690
- 20.1.6 ap-containment 691
- 20.1.7 ap-detection 692
- 20.1.9 ap-ip 695
- 20.1.11 ap-timeout 698
- 20.1.12 ap-udp-port 699
- 20.1.13 auto-select-channels 700
- 20.1.14 broadcast-tx-speed 701
- 20.1.15 client 702
- <MAC/Mask>] 704
- 20.1.16 clrscr 706
- 20.1.18 convert-ap 708
- 20.1.19 country-code 711
- 20.1.20 debug 712
- 20.1.22 dhcp-sniff-state 716
- 20.1.23 dot11-shared-key-auth 717
- 20.1.24 end 718
- 20.1.25 exit 719
- 20.1.27 help 721
- 20.1.28 hotspot 722
- 20.1.29 ids 723
- 20.1.31 mac-auth-local 729
- 20.1.32 manual-wlan-mapping 731
- 20.1.33 mobile-unit 732
- 20.1.34 mobility 733
- 10 high 20 735
- 20.1.37 nas-id 736
- 20.1.38 nas-port-id 737
- 20.1.39 no 738
- 20.1.40 proxy-arp 739
- 20.1.41 qos-mapping 740
- 20.1.42 radio 742
- 20.1.43 rate-limit 756
- 20.1.46 sensor 760
- 20.1.47 service 762
- 20.1.48 show 775
- 20.1.49 smart-rf 778
- 20.1.50 smart-scan-channels 779
- 20.1.51 wlan 780
- should be less than what is 795
- 20.1.52 wlan-bw-allocation 807
- RTLS Instance 809
- 21.1.1 aeroscout 811
- 21.1.2 clear 812
- 21.1.3 clrscr 813
- 21.1.4 end 814
- 21.1.5 espi 815
- 21.1.6 exit 816
- 21.1.7 help 817
- 21.1.8 ekahau 818
- 21.1.9 no 819
- RFSwitch 820
- RFSwitch(config-rtls)# 823
- 21.1.11 rfid 824
- 21.1.12 service 825
- 21.1.13 show 828
- 21.1.14 site 831
- command 832
- 21.1.15 sole 833
- 21.1.16 switch 834
- 21.1.17 zone 835
- 21.1.18 ap 836
- ESPI Instance 837
- 22.1.1 adapter 839
- 22.1.2 clrscr 840
- 22.1.3 end 841
- 22.1.4 exit 842
- 22.1.5 help 843
- 22.1.6 no 844
- 22.1.7 service 845
- 22.1.8 show 846
- RFID Instance 849
- 23.1.1 activate 851
- 23.1.2 clrscr 852
- 23.1.3 end 853
- 23.1.4 exit 854
- 23.1.5 help 855
- 23.1.6 no 856
- 23.1.7 reader 857
- 400 y 400 z 500 859
- RFSwitch(config-rtls-rfid)# 859
- 23.1.8 service 860
- 23.1.9 show 863
- SOLE Instance 867
- 24.1.1 clrscr 869
- 24.1.2 end 870
- 24.1.3 exit 871
- 24.1.4 help 872
- 24.1.5 locate 873
- RFSwitch(config-rtls-sole)# 874
- 24.1.6 no 875
- 24.1.7 redundancy 876
- 24.1.8 service 877
- 24.1.9 show 878
- 24.1.10 rssi-filter 881
- <5-3600> 882
- 24.1.12 mobile-unit 883
- Smart RF Instance 885
- 25.1.1 assignable-power-range 887
- 25.1.2 auto-assign 888
- 25.1.3 clrscr 889
- 25.1.4 end 890
- 25.1.5 exit 891
- 25.1.6 extensive-scan 892
- 25.1.7 help 893
- 25.1.8 hold-time 894
- 25.1.9 no 895
- 25.1.11 radio 903
- 25.1.13 retry-threshold 909
- 25.1.14 run-calibrate 910
- 25.1.15 scan-dwell-time 911
- 25.1.16 schedule-calibrate 912
- 25.1.17 select-channels 913
- 25.1.18 service 914
- 25.1.21 verbose 925
- Role Instance 927
- Command Description mRef 928
- 26.1.1 ap-location 929
- RFSwitch(config-role)# 930
- 26.1.2 authentication-type 931
- 26.1.3 encryption-type 932
- 26.1.4 essid 934
- 26.1.5 group 935
- 26.1.6 ip 936
- 26.1.7 mac 937
- 26.1.8 mu-mac 938
- 26.1.9 clrscr 939
- 26.1.11 end 941
- 26.1.12 exit 942
- 26.1.13 help 943
- 26.1.14 service 944
- 26.1.15 show 945
Related products and manuals for Network switches Motorola RFS6000 - Wireless RF Switch
Network switches Motorola T1/E1 User Manual
(25 pages)
(25 pages)
Network switches Motorola T1/E1 Specifications
(122 pages)
(122 pages)
(31 pages)© 2020, manymanuals.com. All rights reserved. | 0.127 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals