Motorola LI2208 Specifications Page 324
- Page / 416
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
12 - 4 LI2208 Product Reference Guide
Troubleshooting
NOTE If having issues decoding, ensure you are above the bar code before engaging the trigger, and NOT
sweeping the illumination over the bar code during a decode session.
Table 12-1
Troubleshooting
Problem Possible Causes Possible Solutions
Beeper Indications
Linear imager scanner emits
low/high/low beeps.
ADF transmit error. See
Chapter 11, ADVANCED DATA
FORMATTING
for information about
ADF programming.
Invalid ADF rule is detected. See
Chapter 11, ADVANCED DATA
FORMATTING
for information about
ADF programming.
The Code 39 buffer was erased or
there was an attempt to clear or
transmit an empty buffer.
Normal when scanning the Code 39
Buffering
Clear Buffer
bar code or
upon attempt to transmit an empty
Code 39 buffer.
Linear imager scanner emits a
low/high/low/high beep sequence
while it is being programmed.
Out of ADF parameter storage
space.
Erase all rules and re-program with
shorter rules.
Linear imager scanner emits long
low/long high beeps.
Input error, incorrect bar code or
Cancel
bar code was scanned.
Scan the correct numeric bar codes
within range for the parameter
programmed.
Linear imager scanner emits long
low/long high/long low/long high
beeps.
Out of host parameter storage
space.
Scan
Default Parameters on page
7-4
.
Out of memory for ADF rules. Reduce the number of ADF rules or the
number of steps in the ADF rules.
Linear imager scanner emits
high/high/high/low beeps.
RS-232 receive error. Normal during host reset. Otherwise,
set the linear imager's RS-232 parity to
match the host setting.
Linear imager scanner emits
high/low beeps.
The linear imager is buffering
Code 39 data.
Or
Keyboard parameter selected.
Normal.
Or
Enter value using bar code keypad.
Linear imager scanner emits three
long high beeps.
Code 39 buffer is full. Scan the Code 39 bar code without a
leading space or scan
Do Not Buffer
Code 39
on
Code 39 Buffering - Scan
& Store on page 9-34
to transmit
stored Code 29 data.
Linear imager scanner emits four
long low beeps.
A transmission error was
detected in a scanned symbol.
The data is ignored.
This occurs if a unit is not properly
configured. Check option setting.
- PRODUCT REFERENCE 1
- PRODUCT REFERENCE GUIDE 3
- Warranty 4
- Revision History 5
- TABLE OF CONTENTS 7
- Table of Contents vii 9
- Table of Contents ix 11
- Table of Contents xi 13
- ABOUT THIS GUIDE 15
- About This Guide xv 17
- Chapter Descriptions 18
- Notational Conventions 18
- Related Documents 19
- Service Information 19
- CHAPTER 1 GETTING STARTED 21
- Scanner Parts 22
- Configuring the Linear Imager 22
- CHAPTER 2 SCANNING 23
- Table 2-1 24
- SCANNING 2 - 3 25
- Scanning 26
- Hands-Free Scanning 27
- Decode Ranges 28
- CHAPTER 3 USB INTERFACE 29
- Connecting a USB Interface 30
- USB INTERFACE 3 - 3 31
- USB Parameter Defaults 32
- USB INTERFACE 3 - 5 33
- USB Host Parameters 34
- USB Device Type (continued) 35
- *No Delay 37
- USB Ignore Unknown Characters 38
- * Enable Keypad Emulation 39
- * Enable 40
- *Disable Simulated Caps Lock 41
- *No Case Conversion 42
- *Enable USB Static CDC 42
- Optional USB Parameters 43
- * 3 msec 44
- USB INTERFACE 3 - 17 45
- * Disable 46
- Toshiba TEC Host Parameters 47
- * Add Symbol Types 48
- * Add Character Counts 48
- Toshiba TEC Include Header 49
- Toshiba TEC Header Character 50
- USB INTERFACE 3 - 23 51
- * Light LED on Good Decode 51
- Indicate Before Transmission 52
- Indicate After Transmission 52
- ASCII Character Set for USB 53
- Table 3-3 54
- USB INTERFACE 3 - 27 55
- USB INTERFACE 3 - 29 57
- Table 3-4 58
- USB INTERFACE 3 - 31 59
- Table 3-6 60
- Table 3-5 60
- USB INTERFACE 3 - 33 61
- Table 3-8 62
- CHAPTER 4 RS-232 INTERFACE 63
- RS-232 Parameter Defaults 65
- RS-232 Host Parameters 66
- RS-232 INTERFACE 4 - 5 67
- *Standard RS-232 68
- RS-232 Host Types (continued) 69
- *Baud Rate 9600 70
- *1 Stop Bit 71
- *Check For Received Errors 71
- Data Bits (ASCII Format) 72
- Hardware Handshaking 73
- Software Handshaking 75
- ACK/NAK with ENQ 76
- XON/XOFF 76
- *Minimum: 2 sec 77
- *Host: Low RTS 78
- *Minimum: 0 msec 79
- *Normal Operation 80
- RS-232 INTERFACE 4 - 19 81
- Table 4-4 82
- RS-232 INTERFACE 4 - 21 83
- RS-232 INTERFACE 4 - 23 85
- CHAPTER 5 IBM INTERFACE 87
- IBM Parameter Defaults 89
- IBM 468X/469X Host Parameters 90
- Optional IBM Parameters 91
- CHAPTER 6 KEYBOARD WEDGE 93
- INTERFACE 93
- Table 6-1 95
- *IBM AT Notebook 96
- Intra-Keystroke Delay 98
- *Disable Caps Lock On 99
- *Disable Caps Lock Override 100
- *No Convert 100
- *Disable Function Key Mapping 101
- *Disable FN1 Substitution 101
- Send Make and Break 102
- Keyboard Map 103
- Table 6-2 104
- Table 6-3 108
- Table 6-4 109
- Table 6-5 110
- Table 6-6 111
- Table 6-7 113
- MISCELLANEOUS SCANNER 115
- Scanning Sequence Examples 116
- Errors While Scanning 116
- User Preferences 118
- Report Version 119
- Parameter Bar Code Scanning 119
- *Beep After Good Decode 120
- *Medium Tone 121
- *High Volume 122
- Beeper Duration 123
- *Standard (Level) 124
- *Enable Hands-Free Mode 125
- *Auto-discriminate 126
- *Pulsing Pattern 127
- * Enable Low Power Mode 128
- Time Delay to Low Power Mode 129
- * 1 Hour 130
- *5 Minutes 131
- Continuous Bar Code Read 133
- Unique Bar Code Reporting 133
- Decode Session Timeout 134
- *Enable Decoding Illumination 135
- Transmit Code ID Character 136
- Prefix/Suffix Values 137
- Scan Data Transmission Format 138
- *Data As Is 139
- FN1 Substitution Values 140
- *Disable No Read 141
- Parameter # F8h 04h 5Eh 142
- Enter Key 143
- (Carriage Return/Line Feed) 143
- CHAPTER 9 SYMBOLOGIES 145
- Symbology Parameter Defaults 146
- SYMBOLOGIES 9 - 3 147
- Table 9-1 148
- SYMBOLOGIES 9 - 5 149
- Disable All Code Types 150
- *Enable UPC-A 151
- *Enable UPC-E 151
- *Disable UPC-E1 152
- *Enable EAN-8/JAN-8 152
- *Enable EAN-13/JAN-13 153
- *Disable Bookland EAN 153
- Parameter # 10h 154
- *Ignore Supplementals 155
- SYMBOLOGIES 9 - 13 157
- Parameter # 50h 157
- *Combined 158
- *Transmit UPC-A Check Digit 159
- *Transmit UPC-E Check Digit 159
- *Transmit UPC-E1 Check Digit 160
- UPC-A Preamble 161
- UPC-E Preamble 162
- UPC-E1 Preamble 163
- Convert UPC-E to UPC-A 164
- Convert UPC-E1 to UPC-A 164
- *Disable EAN/JAN Zero Extend 165
- *Bookland ISBN-10 165
- *New Coupon Format 166
- *Disable ISSN EAN 167
- Code 128 168
- *Code 128 - Any Length 169
- *Enable GS1-128 170
- *Enable ISBT 128 170
- ISBT Concatenation 171
- *Enable Check ISBT Table 172
- *Code 128 Security Level 1 173
- *Enable Code 39 174
- *Disable Trioptic Code 39 174
- *Disable Code 32 Prefix 175
- * Code 39 - Any Length 176
- *Disable Code 39 Check Digit 177
- *Disable Code 39 Full ASCII 178
- Buffer Data 179
- Clear Transmission Buffer 179
- Transmit Buffer 180
- Code 39 Security Level 181
- * Enable Code 93 182
- * Code 93 - Any Length 183
- *Disable Code 11 184
- SYMBOLOGIES 9 - 41 185
- *Disable 186
- Transmit Code 11 Check Digits 187
- Interleaved 2 of 5 (ITF) 188
- SYMBOLOGIES 9 - 45 189
- Convert I 2 of 5 to EAN-13 191
- *I 2 of 5 Security Level 1 192
- Discrete 2 of 5 (DTF) 193
- *D 2 of 5 - Any Length 194
- Codabar (NW - 7) 195
- Codabar - One Discrete Length 196
- (4 to 60) 196
- Codabar - Any Length 196
- *Disable CLSI Editing 197
- *Disable NOTIS Editing 197
- *Upper Case 198
- *Disable MSI 199
- * MSI - Length Within Range 200
- *One MSI Check Digit 201
- *MOD 10/MOD 10 202
- Chinese 2 of 5 203
- Matrix 2 of 5 204
- SYMBOLOGIES 9 - 61 205
- Matrix 2 of 5 Check Digit 206
- Korean 3 of 5 207
- Inverse 1D 208
- GS1 DataBar 209
- *Enable GS1 DataBar Expanded 210
- SYMBOLOGIES 9 - 67 211
- Parameter # F0h, 8Dh 212
- Redundancy Level 1 213
- Redundancy Level 2 213
- Redundancy Level 3 213
- Redundancy Level 4 213
- *Redundancy Level 1 214
- SYMBOLOGIES 9 - 71 215
- Parameter # 4Dh 215
- *Normal Intercharacter Gaps 216
- CHAPTER 10 123SCAN2 217
- Requirements 218
- CHAPTER 11 ADVANCED DATA 219
- FORMATTING 219
- Using ADF Bar Codes 220
- ADF Bar Code Menu Example 220
- Rule 2: The UPC Scanning Rule 221
- Alternate Rule Sets 221
- Default Rules 223
- ADF Bar Codes 224
- Table 11-1 225
- Special Commands 226
- Quit Entering Rules 227
- Disable Rule Set 228
- Criteria 229
- Code Types (continued) 230
- Code Lengths 233
- Code Lengths (continued) 234
- Specific String at Start 237
- Specific String Search 238
- Any Message OK 238
- Numeric Keypad 239
- Numeric Keypad (continued) 240
- Rule Belongs To Set 241
- Send Data 242
- Send Data (continued) 243
- Setup Field(s) 245
- Move Cursor 246
- Move Cursor (continued) 247
- Skip Ahead 248
- Skip Back 249
- Skip Ahead (continued) 249
- Skip Back (continued) 250
- Send Preset Value 251
- Remove All Spaces 251
- Crunch All Spaces 251
- Stop Space Removal 251
- Remove Leading Zeros 252
- Stop Zero Removal 252
- Pad Data with Spaces 253
- Pad Data with Zeros 257
- Control Characters 262
- Keyboard Characters 267
- Send ALT Characters 281
- Send Alt 285
- Send Keypad Characters 286
- Send Function Key 291
- Send Function Key (continued) 292
- Turn On/Off Rule Sets 304
- Turn Off Rule Set 1 305
- Turn Off Rule Set 2 305
- Turn Off Rule Set 3 305
- Turn Off Rule Set 4 305
- Alphanumeric Keyboard 306
- CHAPTER 12 MAINTENANCE 321
- TROUBLESHOOTING & 321
- TECHNICAL SPECIFICATIONS 321
- Approved Cleaning Agents 322
- Cleaning the Linear Imager 322
- Health Care Linear Imagers 323
- Troubleshooting 324
- Table 12-1 325
- Technical Specifications 327
- Table 12-2 328
- Signal Descriptions 329
- PARAMETERS 331
- Table A-1 332
- APPENDIX B COUNTRY CODES 339
- *US English (North American) 340
- Country Codes (Continued) 341
- Symbol Code Identifiers 355
- Table C-1 356
- AIM Code Identifiers 357
- ]C1AIMID 358
- PROGRAMMING REFERENCE C - 5 359
- APPENDIX D SAMPLE BAR CODES 361
- Interleaved 2 of 5 362
- APPENDIX E NUMERIC BAR CODES 365
- NUMERIC BAR CODES E - 3 367
- ALPHANUMERIC BAR CODES F - 3 371
- ALPHANUMERIC BAR CODES F - 5 373
- ALPHANUMERIC BAR CODES F - 7 375
- ALPHANUMERIC BAR CODES F - 9 377
- ALPHANUMERIC BAR CODES F - 11 379
- ALPHANUMERIC BAR CODES F - 13 381
- ALPHANUMERIC BAR CODES F - 15 383
- ALPHANUMERIC BAR CODES F - 17 385
- Table G-1 387
- ASCII CHARACTER SETS G - 3 389
- ASCII CHARACTER SETS G - 5 391
- Table G-2 392
- ASCII CHARACTER SETS G - 7 393
- Table G-4 394
- ASCII CHARACTER SETS G - 9 395
- Table G-7 396
- Table G-6 396
- ASCII CHARACTER SETS G - 11 397
- Numerics 399
- Index - 3 401
- Index - 5 403
- GLOSSARY 405
- Glossary - 3 407
- Glossary - 5 409
- Glossary - 7 411
- Glossary - 9 413
Related products and manuals for Bar code readers Motorola LI2208
Bar code readers Motorola DS3508 Specifications
(386 pages)
(386 pages)
Bar code readers Motorola DS3508 Specifications
(316 pages)
(316 pages)
Bar code readers Motorola RS507 User Manual
(16 pages)
(16 pages)
(2 pages)
(36 pages)
Bar code readers Motorola MT2070 User's Guide
(560 pages)
(560 pages)
© 2020, manymanuals.com. All rights reserved. | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals