RFS6000 Series RF SwitchInstallation GuideM
LED Codes63.1.4 Fan LED3.1.5 Temperature Status LEDGreen Blinking Green SolidRedundant System failed over and adopting portsGreen BlinkingAltern
LED Codes7Amber BlinkingAmbient Inlet Temperature is above the maximum specified operating temperatureSystem will be held in reset until the issue is
LED Codes83.2 RJ-45 Gigabit Ethernet LEDs3.2.1 RJ-45 Port Speed LED3.2.2 RJ-45 Port Status LEDPort Speed LED EventOff 10 MbpsGreen Solid 100 Mbp
LED Codes93.3 SFP Gigabit Ethernet LEDs3.3.1 SFP Port Speed LED3.3.2 SFP Port Status LEDPort Speed LED EventAmber Solid 1000 MbpsPort Status LED
LED Codes103.4 Management Port LEDs3.4.1 Out of Band Management Port Speed LED3.5 Out of Band Management Port Status LEDPort Speed LED EventOff
Hardware Setup114 Hardware Setup4.1 Cabling InformationThe RFS6010 RF Switch has nine RJ-45 Gigabit Ethernet ports, one Gigabit SFP (fiber) port, o
Hardware Setup12expansion. For software configuration, please see the Motorola RF Switch System Reference available from the Motorola website.4.2
Hardware Setup134.2.1 Installing the Gigabit Ethernet SFP1. Open the bail on the transceiver.2. Insert the SFP transceiver into the corresponding p
Hardware Setup144. Insert the fiber optic cables into the installed transceiver.
Hardware Setup154.3 Connecting USB DevicesThe RFS6010 RF Switch contains one USB port for connecting USB flash storage devices to the switch. The s
MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. Symbol is a registered trademark of Symbol Technologies, Inc.
Hardware Setup164.4 Rack Mount InstructionsTo install the RFS6000 Series RF Switch in a rack:1. The rack mounting brackets are installed at the fac
Hardware Setup174.5 RFS6000 Series RF Switch Console Port SetupTo add the RFS6000 Series RF Switch to the network and prepare it for initial config
Hardware Setup184.6 Supplying Power to the RFS6000 Series RF Switch1. Plug an approved AC power cord into the power connector at the back of the RF
Hardware Setup194.7 Verifying the InstallationView the LEDs on the front panel of the RFS6010 RF Switch to ensure the device is functioning properly.
Regulatory Information205 Regulatory InformationThis regulatory section applies to the RFS-6010. For more information refer to section 6, Part Number
Regulatory Information21Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada..Statement of ComplianceMotorola hereby declar
Regulatory Information22Waste Electrical and Electronic Equipment (WEEE)English: For EU Customers: All products at the end of their life must be retur
Regulatory Information23Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere r
Part Numbers, Support, and Sales246 Part Numbers, Support, and SalesPart NumbersMotorola’s Enterprise Mobility Support CenterIf you have a problem wit
Motorola, Inc. End-User LicenseAgreement257 Motorola, Inc.End-User License AgreementBY DOWNLOADING, INSTALLING, OR USING THE SOFTWARE DESCRIBED IN THI
1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.0 Specifications . . . . . . . . . . . . . .
Motorola, Inc. End-User LicenseAgreement26interrupt, destroy or limit the functionality of any computer software or hardware or telecommunications equ
Motorola, Inc. End-User LicenseAgreement279 INDEMNITY. Licensee agrees that Licensor shall have no liability whatsoever for any use Licensee makes of
Motorola, Inc. End-User LicenseAgreement28
Motorola, Inc. End-User LicenseAgreement29
Motorola, Inc. End-User LicenseAgreement30
Motorola, Inc. End-User LicenseAgreement31
MOTOROLA INC.1303 E. ALGONQUIN ROADSCHAUMBURG, IL 60196http://www.motorola.com72-109855-01 Revision AMarch 2008
4
Introduction11 IntroductionThe Motorola RFS6000 Series RF Switch is a high-performance member of Motorola’s Wireless Switch family. The RFS6000 Series
Introduction21.3 Warnings• Read all installation instructions and site survey reports, and verify correct equipment installation before connecting
Specifications32 Specifications2.1 Physical Specifications2.2 Power Cord SpecificationsA power cord is not supplied with the switch. Use only a
LED Codes43 LED CodesThe RFS6010 RF Switch has four vertically-stacked LEDs on its front panel. Each of the switch’s Gigabit Ethernet ports have two s
LED Codes53.1.1 Start Up / POST (Primary System or Redundant System)3.1.2 Switch Status (Primary System)3.1.3 Switch Status (Redundant System
Comments to this Manuals