Motorola AP 7161 Installation Guide

AP 7161 ACCESS POINTINSTALLATION GUIDE

10 AP 7161 Access Point1.3.3 AP-7161-66S40-JP AntennasPart Number Band GainHeight(inches) DescriptionML-2452-HPAG5A8-01 2.4-5.8 4.5/7.5 11 Outdoor

Installation Guide 111.4 Outdoor PoE Hardware and Mounting AccessoriesThe AP 7161 is a Power over Ethernet (PoE) device. When deployed, the use of a

12 AP 7161 Access Point1.7 Package ContentsCarefully remove all protective packing material from around the AP 7161 Access Point and save the contai

Installation Guide 131.8 Hardware Installation Guidelines1.8.1 PrecautionsBefore installing an AP 7161 model Access Point, verify the following g

14 AP 7161 Access Point1.8.2 Warnings• Read all installation instructions and site survey reports, and verify correct equipment installation before

Installation Guide 151.9 Access Point PlacementObserve the following recommended guidelines to help ensure a successful network deployment:• Identif

16 AP 7161 Access Point1.10.2 AP 7161 Antenna ConnectorsAP 7161 two radio models (AP-7161-66040-US and AP-7161-66040-WR) are configured with six N

Installation Guide 17Ports R3-A and R3-B are reserved for the sensor radio. An appropriate multi band antenna should be mounted on the unit for sensor

18 AP 7161 Access PointThe Ethernet cable from the PoE device (if used) connects to the GE1/POE port on the unit.The GE2 port on the unit can be used

Installation Guide 191.10.4 AP 7161 Grounding ScrewThe grounding screw is located to the right of the GE1/POE port and above the GND symbol.The gro

2 AP 7161 Access PointMOTOROLA SOLUTIONS and the Stylized M Logo are registered in the US Patent & Trademark Office. © Motorola Solutions, Inc. 20

20 AP 7161 Access Point1.11 LED IndicatorsThe AP 7161 Access Point has six LEDs on the top of the Access Point housing. When the Access Point is pos

Installation Guide 21The top housing LEDs have the following display patterns and functionality:1.11.1 Two Radio LEDsA two radio model Access Point

22 AP 7161 Access Point1.11.2 Three Radio LEDsA three radio model Access Point with sensor (P/N AP-7161-66S40-US and AP-7161-66S40-WR) has the foll

Installation Guide 232 AP 7161 Hardware Mounting and InstallationIt is recommended to use the AP 7161 mounting bracket kit (KT-147407-01) for most dep

24 AP 7161 Access PointA torque wrench or ratchet with a 10mm adapter, or an adjustable wrench, can be used to assemble the mounting brackets. A finis

Installation Guide 25The extension arm kit can also be used in combination with the any of the brackets from the mounting bracket kit.The following an

26 AP 7161 Access Point2.2 Pole Mounted InstallationsThe mounting hardware kit and extension arm can be used in various combinations to properly ins

Installation Guide 272. Position the U-bolt on the pole and place the pole mount bracket section on the U bolt. Adjust the two 1/2 inch inner nuts unt

28 AP 7161 Access Point4. Position the Access Point bracket section so that the bottom of the section with the straight (not bevel cut) side is orient

Installation Guide 296. With the Access Point positioned so that the gore vent is facing down, insert the two M6 hex flange screws in the bottom holes

Installation Guide 31.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61.

30 AP 7161 Access PointFor mounting with band clamps:1. Attach the pole mount bracket section at the desired mounting location using band clamps.2. Wi

Installation Guide 313. Position the Access Point bracket section so that the bottom of the section with the straight (not bevel cut) sides is oriente

32 AP 7161 Access Point5. With the Access Point positioned so that the gore vent is facing down, insert the two M6 hex flange screws in the bottom hol

Installation Guide 337. Use a torque wrench or a ratchet and a 10mm socket, or an adjustable wrench, to finish attaching the Access Point bracket sect

34 AP 7161 Access Point3. Using a torque wrench or a ratchet and a 10mm socket, or an adjustable wrench, attach the extension arm to the Access Point

Installation Guide 35An example of using the extension arm with only the pole mount bracket is shown below:2.2.2 Wall Mounted InstallationsFor wall

36 AP 7161 Access Point1. With the open slot connections facing down, attach the angle adjust bracket section at the desired mounting location using f

Installation Guide 37align the top holes on the sides with the top holes on the angle adapter bracket section. Insert two M6 hex flange screws into th

38 AP 7161 Access PointTo use only the extension arm:1. Using a torque wrench or a ratchet and a 10mm socket, or an adjustable wrench, attach the exte

Installation Guide 39To use the extension arm with the mounting hardware kit:1. With the open slot connections facing down, attach the angle adjust br

4 AP 7161 Access Point2.3 AP 7161 VMM Mounting and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412.4 AP 7161 Power Options

40 AP 7161 Access Point3. With the Access Point positioned so that the gore vent is facing down, attach the extension arm to the Access Point using fo

Installation Guide 412.3 AP 7161 VMM Mounting and InstallationThe AP 7161 Vehicle Mounted Modem (VMM) is a software enabled profile within the WiNG

42 AP 7161 Access PointTo install the AP 7161 Access Point VMM:1. Position the AP 7161 VMM upside down with the eight screw holes facing upwards.2. Pu

Installation Guide 433. Put the chassis mount on the flat plate with the key hole and four screw holes aligned.4. Put the stiffener plate on the chass

44 AP 7161 Access Point5. Insert four screws with washers through the holes of the three plates and into the screw holes on the bottom of the VMM.6. U

Installation Guide 452.4 AP 7161 Power Options Using Power over EthernetPower over Ethernet (PoE) is the power source for an AP 7161 Access Point. F

46 AP 7161 Access Point2.5 AP 7161 VMM Power Options The AP 7161 Vehicle Mounted Modem (VMM) is a software enabled profile within the WiNG5 architec

Installation Guide 473 Basic Access Point ConfigurationOnce the Access Point is installed and powered on, complete the following steps to get the devi

48 AP 7161 Access Point3. Enter the default username admin in the Username field.4. Enter the default password motorola in the Password field.5. Click

Installation Guide 49The Introduction screen displays the various actions that can be performed using the wizard under the Function Highlight field.Us

Installation Guide 56.8.2 Radio Frequency Interference Requirements - Canada . . . . . . . . . . . . . . . 706.9 CE Marking and European Economic Are

50 AP 7161 Access Point7. Select Save/Commit within each page to save the updates made to that page's configuration. Select Next to proceed to th

Installation Guide 5110. Select an Access Point Type from the following options: • Virtual Controller AP - When more than one Access Point is deployed

52 AP 7161 Access Point13. The Typical Setup Wizard displays the Network Topology screen to define how the Access Point handles network traffic.14. Se

Installation Guide 5315. Select Next. The Typical Setup Wizard displays the LAN Configuration screen to set the Access Point's LAN interface conf

54 AP 7161 Access Point• DNS Forwarding - Select this option to allow a DNS server to translate domain names into IP addresses. If this option is not

Installation Guide 5519. Select Next. The Typical Setup Wizard displays the RADIUS Server Configuration screen if required.Otherwise, the Typical Setu

56 AP 7161 Access Point21. Select Add User to display the dialog to enter user information to add to the RADIUS server user database.22. Enter the fol

Installation Guide 5728. Select Next. The Typical Setup Wizard displays the Summary and Commit screen to summarize the screens (pages) and settings up

58 AP 7161 Access Point3.1 Antenna Type ConfigurationFor AP 7161 to operate properly, the antenna type and antenna gain must be configured manually.

Installation Guide 594 Specifications4.1 Hardware Specifications4.2 Environmental SpecificationsOperating Voltage 36-57 VDCOperating Current Not t

6 AP 7161 Access Point1 IntroductionPerfect for extending network coverage to outside areas, the AP 7161 brings the latest 802.11n 3x3 Multiple Input

60 AP 7161 Access Point4.3 Radio Specifications* Maximum EIRP may vary based on local standards for the area of deployment.** Operating frequency of

Installation Guide 614.4 Networking and Software Specifications4.5 Approvals* For more country specific regulatory information, please contact Mot

62 AP 7161 Access Point5 Basic TroubleshootingBasic troubleshooting recommendations for the AP 7161 Access Point are listed in the following table:Ind

Installation Guide 636 Regulatory InformationThis device is approved under the Symbol Technologies, Inc. brand. Symbol Technologies, Inc. is a wholly

64 AP 7161 Access Point1 The devices subject to the requirements in this KDB can select the initial channel for operation to avoid TDWRs and apply the

Installation Guide 65We encourage the manufacturers to include information for the users, including the operators and installers, to ensure that they

66 AP 7161 Access Point6.2 TDWR Location InformationSTATE CITY LONGITUDE LATITUDE FREQUENCY TERRAIN ELEVATION(MSL) [ft]ANTENNA HEIGHT ABOVE TERRAIN

Installation Guide 67STATE CITY LONGITUDE LATITUDE FREQUENCY TERRAIN ELEVATION(MSL) [ft]ANTENNA HEIGHT ABOVE TERRAIN [ft]MO SAINT LOUIS W 090 29 21 N

68 AP 7161 Access Point6.3 Wireless Country ApprovalsRegulatory markings are applied to the device signifying the radio(s) are approved for use in t

Installation Guide 696.4.2 Potentially Hazardous AtmospheresYou are reminded of the need to observe restrictions on the use of radio devices in fue

Installation Guide 7accurately locate attacks, rogue devices, and network vulnerabilities in real time and permits both a wired and wireless lockdown

70 AP 7161 Access Point6.8 Radio Frequency Interference Requirements - FCCThis equipment has been tested and found to comply with the limits for a C

Installation Guide 71This device has been designed to operate with the antennas listed in this guide, and having a maximum gain of 8 dBi (2.4 GHz) and

72 AP 7161 Access Point6.11 Other CountriesAustraliaUse of 5 GHz RLAN’s in Australia is restricted in the following band: 5.50 – 5.65 GHz.BrazilRegu

Installation Guide 73Article 14The low power radio-frequency devices shall not influence aircraft security and interfere with legal communications; If

74 AP 7161 Access Point6.12 Waste Electrical and Electronic Equipment (WEEE)English: For EU Customers: All products at the end of their life must be

Installation Guide 75Dansk: Til kunder i EU: Alle produkter skal returneres til Motorola Solutions til recirkulering, når de er udtjent. Læs oplysning

76 AP 7161 Access Point7 Motorola Solutions Support CenterIf you have a problem with your equipment, contact support for your region.Contact informati

Installation Guide 778 AP 7161 Series ROHS ComplianceO：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2

78 AP 7161 Access Point

Installation Guide 79

8 AP 7161 Access Point1.2 AP 7161 HardwareThere are currently four AP 7161 Access Point infrastructure models.The AP 7161 Vehicle Mounted Modem (VMM

Motorola Solutions, Inc.1301 E. Algonquin Rd.Schaumburg, IL 60196-1078, U.S.A.http://www.motorolasolutions.comMOTOROLA, MOTO, MOTOROLA SOLUTIONS and t

Installation Guide 91.3.1 AP 7161 4.9 GHz and 5 GHz Antennas1.3.2 AP 7161 Multi Band AntennasPart Number Band GainHeight(inches)DescriptionML-52