Motorola M68CPU32BUG User Manual Page 41
- Page / 196
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
DEBUG MONITOR COMMANDS
M68CPU32BUG/D REV 1 3-11
BS Block of Memory Search BS
In all three modes information on matches is output to the screen in a four-column format. Only
24 lines of matches are displayed on the screen at a time. A message prints at the bottom of the
screen indicating there are more lines to display. Press any character key to resume output. Press
the BREAK key to cancel the output and exit the command.
If a match (or a mismatch in the case of Mode 3) is found with a series of bytes of memory
whose beginning is within and end is outside of the range, then that match and a message is
output stating that the last match does not lie entirely within the range. The user may search non-
contiguous memory with this command without causing a Bus Error.
EXAMPLES Assume the following data is in memory.
00003000 0000 0045 7272 6F72 2053 7461 7475 733D ...Error Status=
00003010 3446 2F2F 436F 6E66 6967 5461 626C 6553 4F//ConfigTableS
00003020 7461 7274 3A00 0000 0000 0000 0000 0000 tart:...........
CPU32Bug>BS 3000 302F ’Task Status’<CR>
Effective address: 00003000
Mode 1: the string is not found, so a
Effective address: 0000302F message is output.
-not found-
CPU32Bug>BS 3000 302F ’Error Status’<CR>
Effective address: 00003000
Mode 1: the string is found, and the
Effective address: 0000302F address of its first byte is output.
00003003
CPU32Bug>BS 3000 301F ’ConfigTableStart’<CR>
Effective address: 00003000
Mode 1: the string is found, but it ends
Effective address: 0000301F outside of the range, so the address of
00003014 its first byte and a message are output.
-last match extends over range boundary-
CPU32Bug>BS 3000:30 ’t’ ;B<CR>
Effective address: 00003000
Mode 1, using <RANGE> with count
Effective count : &48 and size option: count is displayed in
0000300A 0000300C 00003020 00003023 decimal, and address of each occur-
rence of the string is output.
- M68CPU32BUG DEBUG MONITOR 1
- USER’S MANUAL 1
- M68CPU32BUG/D 1
- TABLE OF CONTENTS 3
- M68CPU32BUG/D REV 1 ii 4
- M68CPU32BUG/D REV 1 iii 5
- M68CPU32BUG/D REV 1 iv 6
- M68CPU32BUG/D REV 1 v 7
- LIST OF FIGURES 8
- LIST OF TABLES 8
- CHAPTER 1 9
- 1.1 INTRODUCTION 9
- 1.2 GENERAL DESCRIPTION 9
- GENERAL INFORMATION 10
- M68CPU32BUG/D REV 1 1-2 10
- 1.3 USING THIS MANUAL 11
- 1.5 SYSTEM RESTART 12
- 1.6 MEMORY REQUIREMENTS 13
- Figure 1-2. BCC Memory Map 14
- M68CPU32BUG/D REV 1 1-7 15
- M68CPU32BUG/D REV 1 1-8 16
- CHAPTER 2 17
- DEBUG MONITOR DESCRIPTION 17
- 2.1 INTRODUCTION 17
- M68CPU32BUG/D REV 1 2-2 18
- M68CPU32BUG/D REV 1 2-3 19
- M68CPU32BUG/D REV 1 2-4 20
- M68CPU32BUG/D REV 1 2-5 21
- M68CPU32BUG/D REV 1 2-6 22
- M68CPU32BUG/D REV 1 2-7 23
- M68CPU32BUG/D REV 1 2-8 24
- M68CPU32BUG/D REV 1 2-9 25
- M68CPU32BUG/D REV 1 2-10 26
- M68CPU32BUG/D REV 1 2-11 27
- 2.6 FUNCTION CODE SUPPORT 28
- M68CPU32BUG/D REV 1 2-13 29
- M68CPU32BUG/D REV 1 2-14 30
- CHAPTER 3 31
- 3.1 INTRODUCTION 31
- M68CPU32BUG/D REV 1 3-2 32
- BC Block of Memory Compare BC 33
- BF Block of Memory Fill BF 35
- BM Block of Memory Move BM 37
- BR Breakpoint Insert BR 39
- BS Block of Memory Search BS 40
- BV Block of Memory Verify BV 43
- DC Data Conversion DC 45
- DU Dump S-Records DU 46
- M68CPU32BUG/D REV 1 3-19 49
- M68CPU32BUG/D REV 1 3-20 50
- GN Go To Next Instruction GN 51
- GO Go Execute User Program GO 53
- M68CPU32BUG/D REV 1 3-26 56
- M68CPU32BUG/D REV 1 3-27 57
- HE Help HE 58
- M68CPU32BUG/D REV 1 3-31 61
- M68CPU32BUG/D REV 1 3-32 62
- M68CPU32BUG/D REV 1 3-33 63
- MA Macro Define/Display MA 64
- MAE Macro Edit MAE 67
- M68CPU32BUG/D REV 1 3-39 69
- MD Memory Display MD 70
- MM Memory Modify MM 72
- MS Memory Set MS 74
- M68CPU32BUG/D REV 1 3-45 75
- M68CPU32BUG/D REV 1 3-46 76
- M68CPU32BUG/D REV 1 3-47 77
- PA Printer Attached PA 78
- PF Port Format PF 79
- RD Register Display RD 82
- RESET Cold/Warm Reset RESET 86
- RM Register Modify RM 87
- RS Register Set RS 88
- SD Switch Directories SD 89
- T Trace T 90
- M68CPU32BUG/D REV 1 3-63 93
- Trace on change of flow: 94
- TM Transparent Mode TM 95
- M68CPU32BUG/D REV 1 3-66 96
- M68CPU32BUG/D REV 1 3-67 97
- M68CPU32BUG/D REV 1 3-68 98
- M68CPU32BUG/D REV 1 3-69 99
- DEBUG MONITOR COMMANDS 100
- M68CPU32BUG/D REV 1 3-70 100
- M68CPU32BUG/D REV 1 3-71 101
- M68CPU32BUG/D REV 1 3-72 102
- CHAPTER 4 103
- ASSEMBLER/DISASSEMBLER 103
- 4.1 INTRODUCTION 103
- 4.2SOURCE PROGRAM CODING 104
- M68CPU32BUG/D 4-3 105
- M68CPU32BUG/D 4-4 106
- Pseudo Registers 107
- Main Processor Registers 107
- M68CPU32BUG/D 4-6 108
- M68CPU32BUG/D 4-7 109
- M68CPU32BUG/D 4-8 110
- M68CPU32BUG/D 4-9 111
- M68CPU32BUG/D 4-10 112
- M68CPU32BUG/D 4-11 113
- 0000D000 6000BF68 BRA *-4096 114
- 0000D000 60FE BRA.B * 114
- 0000D000 4EF90000 D000 JMP * 114
- CHAPTER 5 115
- SYSTEM CALLS 115
- 5.1 INTRODUCTION 115
- 5.2 SYSTEM CALL ROUTINES 116
- M68CPU32BUG/D REV 1 5-3 117
- M68CPU32BUG/D REV 1 5-4 118
- M68CPU32BUG/D REV 1 5-5 119
- COUNT = 3 120
- COUNT = 3? 5<CR> 120
- COUNT = 5 120
- COUNT = 3? <CR> 120
- SYSCALL .CHKBRK 121
- BEQ BREAK 121
- M68CPU32BUG/D REV 1 5-8 122
- M68CPU32BUG/D REV 1 5-9 123
- .ERASLN Erase Line .ERASLN 124
- SYSCALL .INCHR Call .INCHR 125
- M68CPU32BUG/D REV 1 5-12 126
- M68CPU32BUG/D REV 1 5-13 127
- M68CPU32BUG/D REV 1 5-14 128
- MOVE.B D0,-(A7) 129
- Send character in D0 129
- SYSCALL .OUTCHR 129
- To default output port 129
- .OUTSTR .OUTSTR 130
- M68CPU32BUG/D REV 1 5-17 131
- PEA (A0) 132
- Long buffer address 132
- SYSCALL .READLN 132
- M68CPU32BUG/D REV 1 5-19 133
- SYSCALL .RETURN 134
- Return to CPU32Bug 134
- .SNDBRK Send Break .SNDBRK 135
- M68CPU32BUG/D REV 1 5-22 136
- SYSCALL .TM_INI 137
- Initialize timer 137
- .TM_RD Read Timer .TM_RD 138
- SYSCALL .TM_STR0 139
- Start Timer at T=0 .TM_STR0 140
- .WRITDLN .WRITDLN 141
- .WRITELN .WRITELN 143
- CHAPTER 6 145
- DIAGNOSTIC FIRMWARE GUIDE 145
- 6.1 INTRODUCTION 145
- 6.2 DIAGNOSTIC MONITOR 145
- M68CPU32BUG/D REV 1 6-2 146
- M68CPU32BUG/D REV 1 6-3 147
- 6.3 UTILITIES 148
- M68CPU32BUG/D REV 1 6-5 149
- CPU CPU Tests For The MCU CPU 150
- CPU A Register Test CPU A 151
- CPU B Instruction Test CPU B 152
- CPU C Address Mode Test CPU C 153
- M68CPU32BUG/D REV 1 6-10 154
- MT Memory Tests MT 155
- M68CPU32BUG/D REV 1 6-12 156
- MT A Set Function Code MT A 157
- MT B Set Start Address MT B 158
- MT C Set Stop Address MT C 159
- MT D Set Bus Data Width MT D 160
- MT E March Address Test MT E 161
- MT F Walk a Bit Test MT F 162
- MT G Refresh Test MT G 163
- MT H Random Byte Test MT H 164
- MT I Program Test MT I 165
- MT J Test and Set Test MT J 166
- BERR Bus Error Test BERR 167
- M68CPU32BUG/D REV 1 6-24 168
- APPENDIX A 169
- S-RECORD INFORMATION 169
- A.1 INTRODUCTION 169
- A.2 S-RECORD CONTENT 169
- A.3 S-RECORD TYPES 170
- A.4 S-RECORDS CREATION 171
- M68CPU32BUG REV 1 A-4 172
- APPENDIX B 173
- SELF-TEST ERROR MESSAGES 173
- B.1 INTRODUCTION 173
- M68CPU32BUG REV 1 B-2 174
- APPENDIX C 175
- USER CUSTOMIZATION 175
- C.1 INTRODUCTION 175
- C.2 CPU32BUG CUSTOMIZATION 176
- M68CPU32BUG REV 1 C-3 177
- C>DEL TMP.MX<CR> 178
- C>DEL C32B1.MX<CR> 178
- C.3 CUSTOMIZATION TABLE 179
- M68CPU32BUG REV 1 C-6 180
- M68CPU32BUG REV 1 C-7 181
- ROM AUTO BOOT VECTORS 182
- Periodic Interrupt Timer 183
- M68CPU32BUG REV 1 C-10 184
- M68CPU32BUG REV 1 C-11 185
- M68CPU32BUG REV 1 C-12 186
- M68CPU32BUG REV 1 C-13 187
- C.4 COMMUNICATION FORMATS 188
- M68CPU32BUG REV 1 C-15 189
- M68CPU32BUG REV 1 C-16 190
- Platform Board 191
- M68CPU32BUG REV 1 C-18 192
- Offset Value Comment 193
- M68CPU32BUG REV 1 C-20 194
- M68CPU32BUG REV 1 C-21 195
- M68CPU32BUG REV 1 C-22 196
Related products and manuals for TVs & monitors Motorola M68CPU32BUG
TVs & monitors Motorola V60 User's Guide
(120 pages)
(120 pages)
© 2020, manymanuals.com. All rights reserved. | 1.187 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals