Motorola HMSC7075 Specifications download pdf

Introduction

Congratulations on your purchase of the Motorola Wireless Keypad Kit.

This module enables you to arm or disarm your entire Motorola

homesight™ system at once upon entry or exit of your home. Its

security design ensures that only a registered Keypad Key can set the

system.

Using Your Keypad

Position the Keypad module at an entrance to the house, near the

garage door, laundry room door, or front door.

1 Touch your Keypad Key to the Keypad port momentarily to make

digital identification.

in lighted before turning

off and becoming disabled. The Keypad port will blink from there

on to assist you in locating it in the dark.

ate

oors, and

o the

ming or disarming devices.

2 The Keypad emits one short beep to let you know the key was

read.

3 The status LED turns red if the key was not accepted.

4 The status LED turns green to let you know the key was accepted

Push either the Home or Away button, as is appropriate. The

button will flash while the system responds.

When the system finishes responding, the Keypad will beep twice

and the Home/Away Port will briefly rema

How It Works

The Wireless Keypad can communic

with the Wireless System Controller

a distance of up to 60 feet ind

200 feet outdoors. The controller then

relays the Home or Away setting t

Motorola homesight™ program, ar

Installation Overview

Your package contains the following:

DATA

KEY

AWAY

HOME

STATUS

Keypad

Module Keypad

Mounting

2 AA

Batteries Power

Adapter

Discovery

Tool

in Installation Hints.

ing a

otorola homesight™ software

to see that the key has be

5 Mount the module, using e following

the instructions for wall mounting.

(2)

Keys

Base

abletop

Hardware

12V

To nstall your Keypad module:

1 Choose an appropriate location for the Keypad module as

described

2 Install batteries or plug the AC adapter into the wall and the

module.

3 Register the module with your Wireless System Controller us

process called discovery. Refer to your homesight Software User

Guide for instructions on how to discover your Wireless Keypad.

4 Touch your Keypad Key(s) to the Kepypad port and click on

Settings/Key Management in the M

en registered.

ither the tabletop base, or by

DAT A

KEY

AWAY

HOM E

STATUS

Installation Hints

Th Motorola Wireless Keypad module is constructed of UV-resistant

plastic.

ABS

Pleas

•

install

•

reless System Controller depending on indoor or

If battery operation is preferred, pry off the back cover by lifting the

upply would be

ove it, and install

e consider the following points when mounting the module:

If installing the Wireless Keypad outside, it should be shielded

from the elements, such as underneath a porch roof. Do not

the module where it is subjected directly to the elements.

Typically, the module's wireless reception is good up to 60–200

feet from the Wi

outdoor use and the number of obstacles. These can include

metal framing, thick walls, and other wireless devices operating

418 MHz. It is recommended that different positions be tried for

optimal results

•

cover at the bottom area where the AC power s

connected. Lift and slide the cover down to rem

the batteries.

Installing Your Wireless Keypa

Your module can either be mounted on a wall or sit on a horizontal

surface using the included tabletop mount adapter.

Wall Mount Your Wireless Keypad

Warning: When mounting near a window, drilling too close to the glass

could break the glass and possibly cause it to shatter. The window

extends deeper into the frame than can be seen; therefore, ensure

your screw is beyond the glass before drilling.

completed the

at the AC adapter is

3 on to the underside of

1 Using the holes on the drilling template found later in this guide,

mark the position of the holes to be drilled.

For drywall or other composite surfaces use a 7/32" drill bit. Drill a

hole for each of the mounting screws

and insert a plastic wall anchor into

each hole.

For other solid surfaces, use a 1/16"

drill bit. Drill a pilot hole for each of

the mounting screws.

1.6 mm (1/16 inch)

maximum

2 Using the screws provided, secure

the module to the wall. When mounting the screws to the wall,

leave 1/16" (1.6 mm) space between the screw head and the wall.

Using the mounting holes, slide the module down on to the screws

until it is firmly seated.

Table Mount Your Wireless Keypad

The module can be placed on any horizontal

surface.

1 Make sure you have

discovery process.

2 Ensure that fresh batteries have bee

installed or th

connected.

Attach the tabletop adapter by pressing it

the Keypad module.

Wall Mount Drilling Template

Mounting tools: Screwdriver, electric drill or awl. On hard surfaces,

Motorola recommends that you pre-drill ½-inch deep pilot holes with a

drill bit slightly smaller than the module mounting screws before

securing the module to the surface. When mounting a module on

surfaces like s

soft

heetrock, use an awl to punch holes in the material

slightly smaller than the plastic anchors included in the hardware

mounting kit.

The illustration is drawn to a one-to-one scale, which means that it

provides the exact dimensions required to mount the unit.

Drill holes In

these positions

3.00 i

Features and Specifications

Away button

Home button

Data and

status LEDs

• Device signal communication

• LED in module illuminates when activity occurs

• Home and Away LEDs light when either is activated

• Weather resistant

• Hardware and base provided for either wall or table

mounting

• AC power adapter included

Communication frequency: 418 MHz

Typical range outdoors: 200 feet (60 m)

Typical range indoors: 60 feet (18 m)

Dimensions: 3.94"L × 2.32"W × 1.10"H (100mm ×

59mm × 28mm)

Operational temperature/

humidity:

32° to 104° F with 10% to 80%

humidity with all components

operating within manufacturer

thermal limits

Storage temperature: -25° C to 75° C

Controller

DATA

KEY

AWAY

HOME

STATUS

Discovery

button

DISCOVERY

Back View

Keypad port

Feature Locator

1 2

Summary of Contents

Page 1 - Feature Locator

Introduction Congratulations on your purchase of the Motorola Wireless Keypad Kit. This module enables you to arm or disarm your entire Motorola home

Page 2 - Limited Warranty

Troubleshooting Problem SolutionModule will not register with the Wireless System Controller • Ensure that the module's AC adapter is plugged

Comments to this Manuals

No comments

Motorola HMSC7075 Specifications

Browse online or download Specifications for Keyboards Motorola HMSC7075. Motorola HMSC7075 Specifications User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Keyboards Motorola HMSC7075