Motorola MVME2600 Series User Manual Page 94
- Page / 518
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
CM - Concurrent Mode NOCM - No Concurrent Mode
3-26
3
Options
Description
The CM command activates a mode in which everything that
appears on the system console terminal is also echoed to the port
specified by the PORT argument.
PORT is checked for inbound characters. These are also echoed to
the system console terminal. If no port is specified, CM uses port 1
by default.
PORT must already be configured. The baud rate need not be
specified because the port is reconfigured prior to activation. The
preconfiguration of the port is done by using the PF (Port Format)
command. If PORT is not currently assigned, CM displays an error
message.
For any reason you may abort the concurrent mode setup by
pressing the BREAK key. This may be necessary if the modem is not
responding to commands from the debugger.
The NOCM command terminates concurrent mode which was
activated by the CM command. Depending on the device and the
port specified with the CM command, the communication link is
appropriately closed.
Examples
Example1: List all devices supported by the debugger:
PPC1-Bug>CM;A <Return>
Concurrent Devices Supported
Device Name (ID-STRING) Default Baud
DUMB 9600
UDS2662 1200
UDS2980 1200
UDS3382 1200
A List all supported devices.
H Displays whether concurrent mode is active or not, and if it
is, what secondary port number is being used by it.
- Firmware Package 1
- User’s Manual 1
- Parts 1 & 2 1
- Restricted Rights Legend 2
- Contents 7
- List of Tables 15
- List of Figures 17
- 1General Information 19
- PPCBug Implementation 20
- Memory Requirements 21
- Start-up 22
- General Information 23
- Auto Boot 31
- Length Contents Description 33
- Sample ROMboot Routine 34
- Network Auto Boot 36
- Restarting the System 37
- Board Failure 39
- MPU Clock Speed Calculation 40
- Disk I/O Support 41
- Device Probe 42
- Disk I/O Error Codes 45
- Network I/O Support 46
- RARP and ARP Modules 48
- BOOTP Module 48
- TFTP Module 48
- Network Boot Control Module 48
- Network I/O Error Codes 49
- Data and Address Sizes 51
- Byte Ordering 52
- 2Using the Debugger 53
- Command Arguments 54
- ADDR Formats 56
- Using the Debugger 57
- Command Options 58
- Control Characters 59
- Exception Vectors 62
- MPU Registers 62
- Context Switching 63
- Floating Point Support 65
- Single Precision Real 66
- Double Precision Real 66
- Scientific Notation 67
- 3Debugger Commands 69
- Debugger Commands 70
- Command Description 70
- AS - One-Line Assembler 72
- BC - Block of Memory Compare 73
- BF - Block of Memory Fill 75
- H Half-word 78
- $000FFFFF 79
- BM - Block of Memory Move 80
- BR - Breakpoint Insert 83
- NOBR - Breakpoint Delete 83
- BS - Block of Memory Search 85
- BV - Block of Memory Verify 90
- CM - Concurrent Mode 93
- NOCM - No Concurrent Mode 93
- A List all supported devices 94
- CS - Checksum 101
- Examples 102
- Read Data = 01000013 103
- PPC1-Bug> 103
- DC - Data Conversion 105
- DMA - Block of Memory Move 108
- Effective address: C1000000 110
- Effective address: C1FFFFFF 110
- D32 block transfer cycles 112
- DS - One-Line Disassembler 116
- DU - Dump S-Records 117
- ECHO - Echo String 119
- ENV - Set Environment 121
- PPC1-Bug>fork 1 10000 126
- PPC1-Bug>forkwr 1 127
- More stuff in between 138
- GN - Go to Next Instruction 142
- GO - Go Execute User Program 144
- Set a breakpoint 148
- HE - Help 150
- IDLE - Idle Master MPU 154
- IOC - I/O Control for Disk 155
- IOI - I/O Inquiry 158
- T Format a disk track 163
- D Format the entire disk 163
- Example 2: 174
- LO - Load S-Records from Host 176
- MA - Macro Define/Display 182
- NOMA - Macro Delete 182
- M=MD 3000 <Return> 183
- M=GO \0 <Return> 183
- M= <Return> 183
- MAE - Macro Edit 185
- MAL - Enable Macro Listing 187
- NOMAL - Disable Macro Listing 187
- MAR - Load Macros 188
- MAW - Save Macros 190
- MD, MDS - Memory Display 192
- Example 5: 194
- Example 6: 194
- Example 7: 195
- Example 8: 195
- MENU - System Menu 196
- MM - Memory Modify 197
- MMD - Memory Map Diagnostic 201
- MS - Memory Set 203
- MW - Memory Write 204
- Example 3: 205
- NAB - Network Auto Boot 206
- NAP - NAP MPU 207
- NIOC - Network I/O Control 214
- NIOP - Network I/O Physical 220
- <Return> 229
- NPING - Network Ping 231
- PPC1-Bug>OF <Return> 235
- PA - Printer Attach 236
- NOPA - Printer Detach 236
- Command Input 238
- Arguments 238
- Loading: Operating System 244
- Partition Not Bootable 244
- PF - Port Format 246
- NOPF - Port Detach 246
- N Disabled 248
- PFLASH - Program FLASH Memory 251
- RB - ROMboot Enable 256
- NORB - ROMboot Disable 256
- RD - Register Display 258
- REMOTE - Remote 264
- RESET - Cold/Warm Reset 265
- RL - Read Loop 267
- RM - Register Modify 268
- RS - Register Set 271
- RUN - MPU Execution/Status 273
- SD - Switch Directories 275
- SET - Set Time and Date 276
- SROM - SROM Examine/Modify 277
- Examples: 278
- SYM - Symbol Table Attach 279
- NOSYM - Symbol Table Detach 279
- Offset Field Description 280
- Example 4: 281
- T - Trace 284
- Initialize IP and R3, R4: 285
- Trace next instruction: 286
- Trace the next instruction: 287
- Breakpoint is displayed) 287
- TA - Terminal Attach 288
- TIME - Display Time and Date 289
- TM - Transparent Mode 290
- S7056504000091 297
- WL - Write Loop 303
- Part 2 of 2 305
- Conventions 308
- Safety Summary 309
- Safety Depends On You 309
- Disclaimer of Warranty 310
- 4One-Line Assembler/ 311
- Disassembler 311
- Directives 312
- Source Program Coding 313
- Instructions 316
- Addressing Modes 318
- WORD Define Constant Directive 319
- SYSCALL System Call Directive 320
- Entering a Source Line 322
- Entering Branch Operands 323
- Assembler Error Messages 324
- 5System Calls 325
- System Call Routines 326
- System Call function 327
- .INSTAT 332
- <CR> 333
- .READSTR 334
- I/O Support on page 1-23 335
- .READLN 336
- .CHKBRK 337
- .DSKRD 338
- Field descriptions: 339
- .DSKCFIG 341
- Command Packet 342
- Table 5-8. CFGA Fields 349
- .DSKFMT 351
- Entry Conditions 352
- .DSKCTRL 354
- .NETRD 356
- .NETCFIG 358
- Most SigniÞcant Word 360
- .NETFOPN 364
- .NETFRD 366
- .NETCTRL 368
- .OUTCHR 371
- .OUTSTR 372
- .WRITE 373
- .WRITELN 373
- .ERASLN 375
- .WRITD 376
- .WRITDLN 376
- .WRITD .WRITDLN 377
- Z is included if 377
- .SNDBRK 378
- .RTC_TM 380
- .RTC_DT 381
- .RTC_DSP 382
- .RTC_RD 383
- .REDIR_I 385
- .REDIR_O 385
- .RETURN 386
- .BINDEC 387
- .CHANGEV 388
- .STRCMP 389
- .MULU32 390
- .DIVU32 391
- .CHK_SUM 392
- .BRD_ID 393
- .ENVIRON 396
- .PFLASH Function 400
- .DIAGFCN 403
- F 405
- Example 1: .CHKFCN 411
- Example 2: .TESTSTAT 411
- Example 3: .MEMSTAT 412
- Example 4: .ST_NMLIST 413
- .SIOPEPS 415
- .FORKMPU Function 417
- .FORKMPUR Function 418
- .IDLEMPU Function 423
- I/O Control Structure 427
- .IOINFORM 430
- Port Control Structure 431
- .IOCONFIG 432
- .IODELETE 433
- .SYMBOLTA 435
- .SYMBOLTD 437
- Related Documentation 439
- Document Title and Source 441
- Publication 441
- Related Specifications 447
- Related Specifications 449
- BSystem Menu 451
- Go to System Diagnostics 452
- Initiate Service Call 452
- Display System Test Errors 452
- Dump Memory to Tape 452
- System Menu 453
- Tape Dump Example: 454
- Operation 455
- Enter System ID Number: 456
- Enter phone number: 456
- Manual Connection 459
- Terminal Connection 461
- CPPCBug Messages 463
- Other Messages 464
- -not found 466
- OK to proceed (y/n)? 466
- Press “RETURN” to continue 466
- WARM Start 466
- DS-Record Format 467
- S-Record Types 468
- Creating S-Records 470
- S-Record Format 473
- T L A C/D Ch 473
- EDisk and Tape Controllers 475
- PPC1Bug version 1.2 477
- FDisk Status Codes 479
- ATAPI (CD-ROM Drives) 480
- SCSI Firmware Status Codes 481
- GNetwork Controller Devices 487
- HNetwork Communication 489
- Status Codes 489
- Glossary 493
Related products and manuals for PC/workstation barebones Motorola MVME2600 Series
(18 pages)© 2020, manymanuals.com. All rights reserved. | 0.255 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals